Novel CFRP Adhesive Joints and Structures for Offshore Application

Authors: M. R. Abusrea, Shiyi Jiang, Dingding Chen, Kazuo Arakawa

Abstract:

Novel wind-lens turbine designs can augment power output. Vacuum-Assisted Resin Transfer Molding (VARTM) is used to form large and complex structures from a Carbon Fiber Reinforced Polymer (CFRP) composite. Typically, wind-lens turbine structures are fabricated in segments, and then bonded to form the final structure. This paper introduces five new adhesive joints, divided into two groups: one is constructed between dry carbon and CFRP fabrics, and the other is constructed with two dry carbon fibers. All joints and CFRP fabrics were made in our laboratory using VARTM manufacturing techniques. Specimens were prepared for tensile testing to measure joint performance. The results showed that the second group of joints achieved a higher tensile strength than the first group. On the other hand, the tensile fracture behavior of the two groups showed the same pattern of crack originating near the joint ends followed by crack propagation until fracture.

Keywords: Adhesive joints, CFRP, VARTM, resin transfer molding.

Digital Object Identifier (DOI): doi.org/10.5281/zenodo.1110003

References:

[1] Chen D.D., Arakawa K, Jiang S.Y. Novel Joints Developed from Partially Un-Moulded Carbon-Fibre-Reinforced Laminates. Journal of Composite Materials, 2015, Vol. 49(14) 1777–1786.
[2] Lee D. G., Jeong K. S., Kim K. S., et al. Development of the Anthropomorphic Robot with Carbon Fiber Epoxy Composite Materials. Compos. Struct. 1993; 25: 313–324.
[3] Niu M. Airframe Structural Design. 9th Printing. Hong Kong: Conmilit. Press Ltd.; 1997.
[4] Wang Z. Y., Wang L, Guo W, et al. An Investigation on Strain/Stress Distribution around the Overlap End of Laminated Composite Single-Lap Joints. Compos Struct. 2009; 89: 589–595. 3.
[5] Liu F, Zhao L, Mehmood S, et al. A Modified Failure Envelope Method for Failure Prediction of Multi-Bolt Composite Joints. Compos Sci. Technol. 2013; 83: 54–63.
[6] Quaresimin M and Ricotta M. Stress Intensity Factors and Strain Energy Release Rates in Single Lap Bonded Joints in Composite Materials. Compos Sci Technol 2006; 66: 647–656.
[7] Al-Zubaidy H, Al-Mahaidi R and Zhao X-L. Experimental Investigation of Bond Characteristics between CFRP Fabrics and Steel Plate Joints under Impact Tensile Loads. Compos Struct 2012; 94: 510-518.
[8] Fawzia S, Al-Mahaidi R and Zhao X-L. Experimental and Finite Element Analysis of a Double Strap Joint between Steel Plates and Normal Modulus CFRP. Compos Struct 2006; 75: 156–162.
[9] Fawzia S, Zhao XL, Al-Mahaidi R, et al. Bond Characteristics between CFRP and Steel Plates in Double Strap Joints. Int J Adv Steel Constr 2005; 1: 17–27.
[10] LÖbel T., Kolesnikov B, Scheffler S, et al. Enhanced Tensile Strength of Composite Joints by Using Staple-Like Pins: Working Principles and Experimental Validation. Compos. Struct. 2013; 106: 453–460.
[11] Banea M. D., Da Silva L. F. Adhesively Bonded Joints in Composite Material: an Overview. J. Mater Des Appl. 2009; 223:1–18.
[12] Wen-Xue W., Yoshiro T., Terutake M. Galvanic Corrosion-Resistant Carbon Fiber Metal Laminates. 16th Int. Conf. on Composite Materials.
[13] Katnam KB, Comer AJ, Stanley WF, et al. Characterising Pre-Preg and Non-Crimp-Fabric Composite Single Lap Bonded Joints. Int J Adhes Adhes 2011; 31: 679–686.