A Simulation Study of Direct Injection Compressed Natural Gas Spark Ignition Engine Performance Utilizing Turbulent Jet Ignition with Controlled Air Charge

Authors: Siyamak Ziyaei, Siti Khalijah Mazlan, Petros Lappas

Abstract:

Compressed natural gas (CNG) is primarily composed of methane (CH4), and has a lower carbon to hydrogen ratio than other hydrocarbon fuels such as gasoline (C8H18) and diesel (C12H23). Consequently, it has the potential to reduce CO2 emissions compared to conventional fuels. Although Natural Gas (NG) has environmental advantages compared to other hydrocarbon fuels, its main component, CH4, burns at a slower rate compared to the conventional fuels. A higher pressure and leaner cylinder environment will unravel the slow burn characteristic of CH4. Lean combustion and high compression ratios are well-known methods for increasing the efficiency of internal combustion engines. In order to achieve successful a CNG lean combustion in Spark Ignition (SI) engines, a strong ignition system is essential to avoid engine misfires, especially in ultra-lean conditions. Turbulent Jet Ignition (TJI) is an ignition system that employs a pre-combustion chamber to ignite the lean fuel mixture in the main combustion chamber using a fraction of the total fuel per cycle. TJI enables ultra-lean combustion by providing distributed ignition sites through orifices. The fast burn rate provided by TJI enables the ordinary SI engine to be comparable to other combustion systems such as Homogeneous Charge Compression Ignition (HCCI) or Controlled Auto-Ignition (CAI) in terms of thermal efficiency, through the increased levels of dilution without the need of sophisticated control systems. Due to the physical geometry of TJI, which contains small orifices that connect the pre-chamber to the main chamber, providing the right mixture of fuel and air has been identified as a key challenge due to the insufficient amount of air that is pushed into the pre-chamber during each compression stroke. There is also the problem of scavenging which contributed to the factors that reduces the TJI performance. Combustion residual gases such as CO2, CO and NOx from the previous combustion cycle dilute the pre-chamber fuel-air mixture preventing rapid combustion in the pre-chamber. An air-controlled active TJI is presented in this paper in order to address these issues. By supplying air into the pre-chamber at a sufficient pressure, residual gases are exhausted, and the air-fuel ratio is controlled within the pre-chamber, thereby improving the quality of the combustion. An investigation of the 3D combustion characteristics of a CNG-fueled SI engine using a direct injection fuelling strategy employing an air channel in the prechamber is presented in this paper. Experiments and simulations were performed at the Worldwide Mapping Point (WWMP) at 1500 revolutions per minute (rpm), 3.3 bar Indicated Mean Effective Pressure (IMEP), using only conventional spark plugs as a baseline. With a validated baseline engine simulation, the settings were set for all simulation scenarios at λ=1. Following that, the pre-chambers with and without an auxiliary fuel supply were simulated. In the study of (DI-CNG) SI engine, active TJI was observed to perform better than passive TJI and conventional  spark plug ignition. In conclusion, the active pre-chamber with an air channel demonstrated an improved thermal efficiency (ηth) over other counterparts and conventional spark ignition systems.

Keywords: Turbulent Jet Ignition, Active Air Control Turbulent Jet Ignition, Pre-chamber ignition system, Active and Passive Pre-chamber, thermal efficiency, methane combustion, internal combustion engine combustion emissions.

References:

[1] M. C. Turkish, ”3-valve Stratified Charge Engines: Evolvement, Analysis and Progression”, SAE Transactions, vol. 83, 1974, pp. 3483–503. JSTOR.
[online].Accessed: Dec. 08, 2022. Available: http://www.jstor.org/stable/44723973.
[2] E. Toulson et al., ”Visualization of Propane and Natural Gas Spark Ignition and Turbulent Jet Ignition Combustion”, SAE International Journal of Engines, vol. 5, no. 4, pp.1821-1835, 2012, doi: https://doi.org/10.4271/2012-32-0002.
[3] A. De, D. S. K. Ting, and M. D. Checkel, ”The Effects of Temperature and Pressure on Stretched, Freely Propagating, Premixed, Laminar Methane-Air Flame, SAE Technical Paper Series. SAE International, 2006, doi: 10.4271/2006-01-0494.
[4] R. Amirante, E. Distaso, P. Tamburrano, and R. D. Reitz, “Laminar flame speed correlations for methane, ethane, propane and their mixtures, and natural gas and gasoline for spark-ignition engine simulations,” Int. J. Engine Res., vol. 18, no. 9, pp. 951–970, Nov. 2017, doi: 10.1177/1468087417720018.
[5] W. P. Attard, N. Fraser, P. Parsons, and E. Toulson, “A Turbulent Jet Ignition Pre-Chamber Combustion System for Large Fuel Economy Improvements in a Modern Vehicle Powertrain,” SAE Int. J. Engines, vol. 3, no. 2, pp. 20–37, 2010, doi: 10.4271/2010-01-1457.
[6] S. Couet, P. Higelin, and B. Moreau, “APIR: A New Firing Concept for the Internal Combustion Engines - sensitivity to knock and in-cylinder aerodynamics,” SAE Tech. Pap., 2001, doi: 10.4271/2001-01-1954.
[7] D. K. Park, H. S. Kim, and W. T. Kim, “Study of Flame Propagation for Different Combustion Chamber Configurations in an SI Engine,” SAE Technical Paper Series. SAE International, 1997, doi: 10.4271/970876.
[8] W. P. Attard, H. Blaxill, E. K. Anderson, and P. Litke, “Knock Limit Extension with a Gasoline Fueled Pre-Chamber Jet Igniter in a Modern Vehicle Powertrain,” SAE Int. J. Engines, vol. 5, no. 3, pp. 1201–1215, 2012, doi: 10.4271/2012-01-1143.
[9] T. Kuo and R. D. Reitz, “Computation of Premixed-Charge Combustion in Pancake and Pent-Roof Engines,” SAE Technical Paper Series. SAE International, 1989, doi: 10.4271/890670.
[10] O. Hadded and I. Denbratt, “Turbulence Characteristics of Tumbling Air Motion in Four-Valve S.I. Engines and their Correlation with Combustion Parameters,” Feb. 1991, doi: 10.4271/910478.
[11] D. Sankesh, J. Edsell, S. Mazlan, and P. Lappas, “Comparative study between early and late injection in a natural-gas fuelled spark-ignited direct-injection engine,” Energy Procedia, vol. 110, pp. 275–280, 2017, doi:10.1016/j.egypro.2017.03.139
[12] J. Heywood, ”Internal combustion engine fundamentals”, 2nd Edition, Vol. 2.12, McGraw-Hill, 2018, doi:1260116107. Available: https://www.accessengineeringlibrary.com/content/book/9781260116106
[13] D. Takahashi, K. Nakata, Y. Yoshihara, and T. Omura, “Combustion Development to Realize High Thermal Efficiency Engines,” SAE Int. J. Engines, vol. 9, no. 3, pp. 1486–1493, 2016, doi: https://doi.org/10.4271/2016-01-0693.
[14] Q. A. Abass and M. T. Chaichan, “Study of NOx Emissions of S.I. Engine Fueled with Different Kinds of Hydrocarbon Fuels and Hydrogen,” Al-Khwarizmi Eng. J., vol. 6, no. 2, 2010, Accessed: Mar. 08, 2022.
[Online]. Available: https://www.iasj.net/iasj/article/2293.
[15] S. Goto, T. Fukuda, and Y. Ono, “Study on NOx Formation and Reduction of Lean-Burn Spark-Ignited Gas Engine with Pre-Combustion Chamber,” Trans. JAPAN Soc. Mech. Eng. Ser. B, vol. 64, no. 623, pp. 2332–2339, 1998, doi: 10.1299/kikaib.64.2332.