Out-of-Plane Bending Properties of Out-of-Autoclave Thermosetting Prepregs during Forming Processes

Authors: Hassan A. Alshahrani, Mehdi H. Hojjati

Abstract:

In order to predict and model wrinkling which is caused by out of plane deformation due to compressive loading in the plane of the material during composite prepregs forming, it is necessary to quantitatively understand the relative magnitude of the bending stiffness. This study aims to examine the bending properties of out-of-autoclave (OOA) thermosetting prepreg under vertical cantilever test condition. A direct method for characterizing the bending behavior of composite prepregs was developed. The results from direct measurement were compared with results derived from an image-processing procedure that analyses the captured image during the vertical bending test. A numerical simulation was performed using ABAQUS to confirm the bending stiffness value.

Keywords: Bending stiffness, out of autoclave prepreg, forming process, numerical simulation.

Digital Object Identifier (DOI): doi.org/10.5281/zenodo.1111771

References:

[1] J. S. Lightfoot, M. R. Wisnom, and K. Potter, “Defects in woven preforms: Formation mechanisms and the effects of laminate design and layup protocol,” Compos. Part A: Appl. Sci. Manuf., vol. 51, pp. 99–107, Aug. 2013.
[2] A. C. Long, Ed., Composites Forming Technologies. Richmond: Taylor & Francis, 2007, pp. 1–328.
[3] P. Boisse, N. Hamila, E. Vidal-Sallé, and F. Dumont, “Simulation of wrinkling during textile composite reinforcement forming. Influence of tensile, in-plane shear and bending stiffnesses,” Compos. Sci., vol. 71, pp. 683–692, Mar. 2011.
[4] H. Alshahrani and M. Hojjati, “Optimum processing parameters for hot drape forming of out-of-autoclave prepreg over complex shape using a double diaphragm technique,” in Proc. 20th ICCM Conf., Copenhagen, Denmark, 2015.
[5] H. Alshahrani, R. Mohan, and M. Hojjati, “Experimental investigation of in-plane shear deformation of out-of-autoclave prepreg,” Int. J. Compos. Mater. vol. 5, pp. 81–87, May 2015.
[6] S. P. Haanappel, R. H. W. ten Thije, U. Sachs, B. Rietman, and R. Akkerman, “Formability analyses of uni-directional and textile reinforced thermoplastics,” Compos. Part A: Appl. Sci. Manuf., vol. 56, pp. 80–92, Jan. 2014.
[7] B. Liang, N. Hamila, M. Peillon, and P. Boisse, “Analysis of thermoplastic prepreg bending stiffness during manufacturing and of its influence on wrinkling simulations,” Compos. Part A: Appl. Sci. Manuf., vol. 67, pp. 111–122, Dec. 2014.
[8] T. A. Martin, D. Bhattacharyya, and I. F. Collins, “Bending of fibre-reinforced thermoplastic sheets,” Compos. Manuf., vol. 6, pp. 177–187, 1995.
[9] J. Wang, A. Long, and M. Clifford, “Experimental measurement and predictive modelling of bending behaviour for viscous unidirectional composite materials,” Int. J. Mater. Form., vol. 3, pp. 1253–1266, Sept. 2010.
[10] C. H. Ten Hove, “Bending of CF/PEEK prepregs,” Master’s Thesis, University of Twente, 2012.
[11] A. Margossian, S. Bel, and R. Hinterhoelzl, “Bending characterisation of a molten unidirectional carbon fibre reinforced thermoplastic composite using a Dynamic Mechanical Analysis system,” Compos. Part A: Appl. Sci. Manuf., vol. 77, pp. 154–163, Oct. 2015.
[12] D. Soteropoulos, K. Fetfatsidis, J. A. Sherwood, and J. Langworthy, “Digital method of analyzing the bending stiffness of non‐crimp fabrics,” in AIP Conf. Proc., Belfast, 2011, pp. 913–917.
[13] L. M. Dangora, C. J. Mitchell, and J. A. Sherwood, “Predictive model for the detection of out-of-plane defects formed during textile-composite manufacture,” Compos. Part A: Appl. Sci. Manuf., vol. 78, pp. 102–112, Nov. 2015.