Improvement of Frictional Coefficient of Modified Shoe Soles onto Icy and Snowy Road by Tilting of Added Glass Fibers into Rubber

Authors: Shunya Wakayama, Kazuya Okubo, Toru Fujii, Daisuke Sakata, Noriyuki Kado, Hiroshi Furutachi

Abstract:

The purpose of this study is to propose an effective method to improve frictional coefficient between shoe rubber soles with added glass fibers and the surfaces of icy and snowy road in order to prevent slip-and-fall accidents by the users. The additional fibers into the rubber were uniformly tilted to the perpendicular direction of the frictional surface, where tilting angles were -60, -30, +30, +60, 90 degrees and 0 (as normal specimen), respectively. It was found that parallel arraignment was effective to improve the frictional coefficient when glass fibers were embedded in the shoe rubber, while perpendicular to normal direction of the embedded glass fibers on the shoe surface was also effective to do that once after they were exposed from the shoe rubber with its abrasion. These improvements were explained by the increase of stiffness against the shear deformation of the rubber at critical frictional state and adequate scratching of fibers when fibers were protruded in perpendicular to frictional direction, respectively. Most effective angle of tilting of frictional coefficient between rubber specimens and a stone was perpendicular (= 0 degree) to frictional direction. Combinative modified rubber specimen having 2 layers was fabricated where tilting angle of protruded fibers was 0 degree near the contact surface and tilting angle of embedded fibers was 90 degrees near back surface in thickness direction to further improve the frictional coefficient. Current study suggested that effective arraignments in tilting angle of the added fibers should be applied in designing rubber shoe soles to keep the safeties for users in regions of cold climates.

Keywords: Frictional coefficient, icy and snowy road, shoe rubber soles, tilting angle.

Digital Object Identifier (DOI): doi.org/10.5281/zenodo.1110303

References:

[1] Chuansi G, John A, “The assessment of the integration of slip resistance, thermal insulation and wearability of footwear on icy surfaces”, Safety Science, vol.40, pp.613–624, 2002
[2] Grönqvist, Raoul, and Mikko Hirvonen. “Slipperiness of footwear and mechanisms of walking friction on icy surfaces.” International Journal of Industrial Ergonomics, vol.16, No.3, 1995 191-200.
[3] Gao, Chuansi, et al. “The effect of footwear sole abrasion on the coefficient of friction on melting and hard ice”, International journal of industrial ergonomics, vol. 31, No.5, pp.323-330, 2003.
[4] Yasuhiro Nagata, Yasuhiro Kaneda, Mami Tomita, “Analysis of Pedestrian’s Falls on Winter Road in Sapporo”, Ice and Snow in Hokkaido, No,33, pp.157-160, 2014
[5] Kuroiwa Daisuke. “The kinetic friction on snow and ice”, Journal of Glaciology, vol.19, 1978 141-152.
[6] Liu, Liwen, et al. “Friction measurements on “anti-slip” floors under shoe sole, contamination, and inclination conditions.” Safety science, vol.48, No.10, pp.1321-1326, 2010
[7] Aschan, Carita, et al. “Slip resistance of oil resistant and non-oil resistant footwear outsoles in winter conditions”, Safety science, vol.43, No.7, pp.373-389, 2005
[8] Li, Kai Way, and Chin Jung Chen. “Effects of tread groove orientation and width of the footwear pads on measured frictional coefficients”, Safety Science, vol.43, No.7, pp.391-405, 2005
[9] Skouvaklis, Gerasimos, Jane R. Blackford, and Vasileios Koutsos. “Friction of rubber on ice: A new machine, influence of rubber properties and sliding parameters”, Tribology International, Vol.49, pp.44-52, 2012.
[10] Tokiwa. K, Tsuruga. T, Misawa. K, Arisawa. J, “Fundamental study of a winter road surface distinction aiming at the development of winter shoes”, vol.70, pp.11-15, 2004
[11] Hsu, Jennifer, and Geoff Fernie. “Maximum Achievable Inclines for Footwear While Walking on Icy Slopes and Cross-Slopes.”
[12] Yamaguchi, Takeshi, et al. “Efficacy of a rubber outsole with a hybrid surface pattern for preventing slips on icy surfaces”. Applied Ergonomics vol.51pp.9-17, 2015
[13] Wada. N, Uchiyama. Y, Masumi. K, “Effect of abraded surface roughness and load on the friction of short fiber reinforced rubber composites”, Rubber, vol.66, No.3, pp.189-198, 1993