Calibration of the Discrete Element Method Using a Large Shear Box

Authors: Corné J. Coetzee, Etienne Horn

Abstract:

One of the main challenges in using the Discrete Element Method (DEM) is to specify the correct input parameter values. In general, the models are sensitive to the input parameter values and accurate results can only be achieved if the correct values are specified. For the linear contact model, micro-parameters such as the particle density, stiffness, coefficient of friction, as well as the particle size and shape distributions are required. There is a need for a procedure to accurately calibrate these parameters before any attempt can be made to accurately model a complete bulk materials handling system. Since DEM is often used to model applications in the mining and quarrying industries, a calibration procedure was developed for materials that consist of relatively large (up to 40 mm in size) particles. A coarse crushed aggregate was used as the test material. Using a specially designed large shear box with a diameter of 590 mm, the confined Young’s modulus (bulk stiffness) and internal friction angle of the material were measured by means of the confined compression test and the direct shear test respectively. DEM models of the experimental setup were developed and the input parameter values were varied iteratively until a close correlation between the experimental and numerical results was achieved. The calibration process was validated by modelling the pull-out of an anchor from a bed of material. The model results compared well with experimental measurement.

Keywords: Discrete Element Method (DEM), calibration, shear box, anchor pull-out.

Digital Object Identifier (DOI): doi.org/10.5281/zenodo.1105607

References:

[1] L. K. Nordell, “Particle Flow Modelling: Transfer chutes and other applications,” in International Materials Handling Conference (BELTCON 9), Johannesburg, South Africa, 1997.
[2] D. B. Hastie, A. P. Grima, P. W. Wypych, “Validation of particle flow through a conveyor transfer hood via particle velocity analysis,” in 2nd International Conference and Exhibition on Storage, Handling and Transporting Bulk (Bulk Europe 2008), Prague, Czech Republic, 2008.
[3] T. Gröger, A. Katterfeld, “On the numerical calibration of discrete element models for the simulation of bulk solids,” in Conveying and Handling of Particulate Solids (CHoPS-05), Sorrento, Italy, 2006
[4] B. Tijskens, Van Besin, Vandewalle, Ramon, “Large scale DEM,” in Conveying and Handling of Particulate Solids (CHoPS-05), Sorrento, Italy, 2006.
[5] A. Grima, P. Wypych, “Investigation into calibration of discrete element model parameters for scale-up and validation of particle-structure interactions under impact conditions,” Powder Technology, vol. 212, pp. 198-209, 2011.
[6] R. Annabattula, Y. Gan, M. Kamlah, “Mechanics of binary and polydisperse spherical pebble assembly,” Fusion Engineering and Design, vol. 87, pp. 853-858, 2012.
[7] I. Cavarretta, C. O'Sullivan, E. Ibraim, M. Lings, S. Hamlin, D. M. Wood, “Characterization of artificial spherical particles for DEM validation studies,” Particuology, vol. 10, pp. 209-220, 2012.
[8] L. Vu-Quoc, X. Zhang, O. R. Walton, “A 3-D discrete-element method for dry granular flows of ellipsoidal particles,” Computational Methods in Applied Mechanics and Engineering, vol. 187, pp. 483 528, 2000.
[9] C. Gonzalez-Montellano, J. Fuentes, E. Ayuga-Tellez, F. Ayuga, “Determination of the mechanical properties of maize grains and olives required for use in DEM simulations,” Journal of Food Engineering, vol. 111, pp. 553-562, 2012.
[10] C. Gonzalez-Montellano, E. Gallego, A. Rami¬rez-Gomez, F. Ayuga, “Three dimensional discrete element models for simulating the filling and emptying of silos: Analysis of numerical results,” Computers & Chemical Engineering, vol. 40, pp. 22-32, 2012.
[11] C. J. Coetzee, D. N. J. Els, “Calibration of discrete element parameters and the modelling of silo discharge and bucket filling,” Computers and Electronics in Agriculture, vol. 65, pp. 198-212, 2009.
[12] C. J. Coetzee, D. N. J. Els, “Calibration of granular material parameters for DEM modelling and numerical verification by blade–granular material interaction,” Journal of Terramechanics, vol. 46, pp. 15–26, 2009.
[13] C. J. Coetzee, D. N. J. Els, “The numerical modelling of excavator bucket filling using DEM,” Journal of Terramechanics, vol. 46, pp. 217– 227, 2009.
[14] C. J. Coetzee, D. N. J. Els, G. F. Dymond, “Discrete element parameter calibration and the modelling of dragline bucket filling,” Journal of Terramechanics, vol. 47, no. 1, pp. 33–44, 2010.
[15] J. Mak, Y. Chen, M. Sadek, “Determining parameters of a discrete element model for soil-tool interaction,” Soil and Tillage Research, vol. 118, pp. 117-122, 2012.
[16] H. Tanaka, M. Momozu, A. Oida, M. Yamazaki, “Simulation of soil deformation and resistance at bar penetration by the distinct element method,” Journal of Terramechanics, vol. 37, pp. 41-56, 2000.
[17] Y. Franco, D. Rubinstein, I. Shmulevich, “Determination of discrete element model parameters for soil-bulldozer blade interaction,” in Proc. of the 15th international conference of the ISTVS, Hayama, Japan, 2005.
[18] Z. Asaf, D. Rubinstein, I. Shmulevich, “Determination of discrete element model parameters using in-situ tests and inverse solution techniques,” in Proc. of the 15th international conference of the ISTVS, Hayama, Japan, September 2005.
[19] Z. Asaf, D. Rubinstein, I. Shmulevich, “Determination of discrete element model parameters required for soil tillage,” Soil Till. Res., vol. 92, no. 2, pp. 227–242, 2007.
[20] Itasca, PFC3D, Particle Flow Code in 3 Dimensions, User's Guide, 4th edition, (www.itascacg.com), 2008.
[21] P. A. Cundall, O. D. L. Strack, “A discrete numerical method for granular assemblies,” Geotechnique, vol. 29, pp. 47–65, 1979.
[22] O.R. Walton, R.L. Braun, “Viscosity, granular-temperature, and stress calculations for shearing assemblies of inelastic, frictional disks,” J. Rheol., vol. 30, pp. 949–980, 1986.
[23] H. A. Navarro, M. P. de Souza Braun, “Determination of the normal spring stiffness coefficient in the linear spring–dashpot contact model of discrete element method,” Powder Technology, vol. 246, pp. 707–722, 2013.
[24] C. J. Coetzee, S. G. Lombard, “The destemming of grapes: Experiments and discrete element modelling,” Biosystems Engineering, vol. 114, pp. 232-248, 2013.
[25] P. W. Cleary, M. L. Sawley, “Three-dimensional modelling of industrial granular flows,” Second International Conference on CFD in the Minerals and Process Industries, 1999.
[26] C. Hogue, “Shape representation and contact detection for discrete element simulations of arbitrary geometries,” Engineering Computations, vol. 15, no. 3, pp. 374-390, 1998.
[27] D. Zhang, W. J. Whiten, “The calculation of contact forces between particles using spring and damping models,” Powder Technology, vol. 88, pp. 59-64, 1996.
[28] J. W. Carson, H. Wilms, “Development of an international standard for shear testing,” Powder Technology, vol. 167, no. 1, pp. 1-9, 2006.
[29] J. Härtl, J. Y. Ooi, “Experiments and simulations of direct shear tests: porosity, contact friction and bulk friction,” Granular Material, vol. 10, no. 4, pp. 263-271, 2008.
[30] K. H. Head, Manual of Soil Laboratory Testing, Volume 2: Permeability, Shear Strength and Compressibility Tests, Pentech Press, London, England, 1981.
[31] J. van der Linde, Discrete element modeling of a vibratory subsoiler, M.Sc. Thesis, Department of Mechanical and Mechatronic Engineering, University of Stellenbosch, Matieland, South Africa, 2007.
[32] G. K. P. Barrios, R M. de Carvalho, A. Kwade, L. M. Tavares, “Contact parameter estimation for DEM simulation of iron ore pellet handling,” Powder Technology, vol. 248, pp. 84-93, 2013.
[33] J. Wiącek, M. Molenda, J. Horabik, J. Y. Ooi, “Influence of grain shape and intergranular friction on material behavior in uniaxial compression: Experimental and DEM modeling,” Powder Technology, vol. 217, pp. 435–442, 2012.
[34] A. Grima, P. Wypych, “Development and validation of calibration methods for discrete element modelling,” Granular Matter vol. 13, pp. 127-132, 2011b.
[35] M. Obermayr, C. Vrettos, P. Eberhard, T. Dauwel, “A discrete element model and its experimental validation for the prediction of draft forces in cohesive soil,” Journal of Terramechanics, vol. 53, pp.93–104, 2014.
[36] M. Ucgul, J. M. Fielke, C. Saunders, “Three-dimensional discrete element modelling of tillage: Determination of a suitable contact model and parameters for a cohesionless soil,” Biosystems Engineering, vol. 121, pp. 105-117, 2014.
[37] K. H. Head, Soil Technicians’ Handbook, London, Pentech Press, 1989.
[38] C. J. Coetzee, R. G. Nel, “Calibration of discrete element properties and the modelling of packed rock beds,” Powder Technology, vol. 264, pp. 332–342, 2014.
[39] A. F. Cabalar, “Applications of the oedometer, triaxial and resonant column tests to the study of micaceous sands,” Engineering Geology, vol. 112, pp. 21–28, 2010.
[40] Y-C. Chung, J. Y. Ooi, “A study of influence of gravity on bulk behaviour of particulate solid,” Particuology, vol. 6, pp. 467–474, 2008.
[41] Y. Xu, K. D. Kafui, C. Thornton, G. Lian, “Effects of Material Properties on Granular Flow in a Silo Using DEM Simulation,” Particulate Science and Technology, vol. 20 pp. 109-124, 2002.
[42] S. Lommen, D. Schott, G. Lodewijks, “DEM speedup: Stiffness effects on behavior of bulk material,” Particuology, vol. 12, pp. 107-112, 2014.
[43] J. Härtl, J. Y. Ooi, “Experiments and simulations of direct shear tests: porosity, contact friction and bulk friction,” Granular Matter, vol. 10, pp. 263–271, 2008.