Search results for: Schiff base ligands

Authors: Gabrielle Peck, Ryan Hayes

Abstract:

Four façade systems were tested using a reduced height BS 8414-2 (5 m) test rig. An L-shaped masonry test wall was clad with three types of insulation and an aluminum composite panel with a non-combustible filling (meeting Euroclass A2). A large (3 MW) wooden crib was ignited in a recess at the base of the L, and the fire was allowed to burn for 30 minutes. Air velocity measurements and gas samples were taken from the main ventilation duct and also a small additional ventilation duct, like those in an apartment bathroom or kitchen. This provided a direct route of travel for smoke from the building façade to a theoretical room using a similar design to many high-rise buildings where the vent is connected to (approximately) 30 m³ rooms. The times to incapacitation and lethality of the effluent were calculated for both the main exhaust vent and for a vent connected to a theoretical 30 m³ room. The rainscreen façade systems tested were the common combinations seen in many tower blocks across the UK. Three tests using ACM A2 with Stonewool, Phenolic foam, and Polyisocyanurate (PIR) foam. A fourth test was conducted with PIR and ACM-PE (polyethylene core). Measurements in the main exhaust duct were representative of the effluent from the burning wood crib. FEDs showed incapacitation could occur up to 30 times quicker with combustible insulation than non-combustible insulation, with lethal gas concentrations accumulating up to 2.7 times faster than other combinations. The PE-cored ACM/PIR combination produced a ferocious fire, resulting in the termination of the test after 13.5 minutes for safety reasons. Occupants of the theoretical room in the PIR/ACM A2 test reached a FED of 1 after 22 minutes; for PF/ACM A2, this took 25 minutes, and for stone wool, a lethal dose measurement of 0.6 was reached at the end of the 30-minute test. In conclusion, when measuring smoke toxicity in the exhaust duct, there is little difference between smoke toxicity measurements between façade systems. Toxicity measured in the main exhaust is largely a result of the wood crib used to ignite the façade system. The addition of a vent allowed smoke toxicity to be quantified in the cavity of the façade, providing a realistic way of measuring the toxicity of smoke that could enter an apartment from a façade fire.

Keywords: smoke toxicity, large-scale testing, BS8414, FED

Procedia PDF Downloads 60

Authors: Attila Kiss, Erzsébet Némedi, Zoltán Naár

Abstract:

Due to the rapidly growing number of conscious customers in the recent years, more and more people look for products with positive physiological effects which may contribute to the preservation of their health. In response to these demands Food Science Research Institute of Budapest develops and introduces into the market new functional foods of guaranteed positive effect that contain bioactive agents. New, efficient technologies are also elaborated in order to preserve the maximum biological effect of the produced foods. The main objective of our work was the development of new functional biscuits fortified with physiologically beneficial ingredients. Bakery products constitute the base of the food nutrients’ pyramid, thus they might be regarded as foodstuffs of the largest consumed quantity. In addition to the well-known and certified physiological benefits of lysine, as an essential amino acid, a series of antioxidant type compounds is formed as a consequence of the occurring Maillard-reaction. Progress of the evoked Maillard-reaction was studied by applying diverse sugars (glucose, fructose, saccharose, isosugar) and lysine at several temperatures (120-170°C). Interval of thermal treatment was also varied (10-30 min). The composition and production technologies were tailored in order to reach the maximum of the possible biological benefits, so as to the highest antioxidant capacity in the biscuits. Out of the examined sugar components, theextent of the Maillard-reaction-driven transformation of glucose was the most pronounced at both applied temperatures. For the precise assessment of the antioxidant activity of the products FRAP and DPPH methods were adapted and optimised. To acquire an authentic and extensive mechanism of the occurring transformations, Maillard-reaction products were identified, and relevant reaction pathways were revealed. GC-MS and HPLC-MS techniques were applied for the analysis of the 60 generated MRPs and characterisation of actual transformation processes. 3 plausible major transformation routes might have been suggested based on the analytical result and the deductive sequence of possible occurring conversions between lysine and the sugars.

Keywords: Maillard-reaction, lysine, antioxidant activity, GC-MS and HPLC-MS techniques

Procedia PDF Downloads 482

Authors: Khosro Mohammadi

Abstract:

In order to study the effect of different resources of farmyard manure, compost and biofertilizers on grain yield and quality of canola (Talaieh cultivar), an experiment was conducted at Kurdistan region. Experimental units were arranged in split-split plots design based on randomized complete blocks with three replications. Main plots consisted of two locations with difference in soil texture (L1): Agricultural Research Center of Sanandaj and (L2): Islamic Azad University of Sanandaj, as location levels. Also, five strategies for obtaining the base fertilizer requirement including (N1): farmyard manure; (N2): compost; (N3): chemical fertilizers; (N4): farm yard manure + compost and (N5): farm yard manure + compost + chemical fertilizers were considered in split plots. Four levels of biofertilizers were (B1): Bacillus lentus and Pseudomonas putida; (B2): Trichoderma harzianum; (B3): Bacillus lentus and Pseudomonas putida & Trichoderma harzianum; and (B4): control. Results showed that location, different resources of fertilizer and interactions of them have a significant effect on grain yield. The highest grain yield (4660 kg/ha) was obtained from treatment, that farmyard manure, compost and biofertilizers were co application in clay loam soil (Gerizeh station). Different methods of fertilization have a significant effect on leaf chlorophyll. Highest amount of chlorophyll (38 Spad) was obtained from co application of farmyard manure, chemical fertilizers and compost (N5 treatment). Location, basal fertilizers and biofertilizers have a significant effect on N, S and N/S of canola seed. Oil content was decreased in Gerizeh station, but oil yield had a significant increasing than Azad University station. Co application of compost and farmyard manure produced highest percent of oleic acid (61.5 %) and linoleic acid (22.9 %). Co application of compost and farmyard manure has a significant increase in oleic acid and linoleic acid. Finally, L1N5B3 treatment, that compost, farmyard manure and biofertilizers were co application in Gerizeh station in compare to other treatments, selected as a best treatment of experiment.

Keywords: soil texture, organic fertilizer, chemical fertilizer, oil, Canola

Procedia PDF Downloads 403

Authors: Rui-heng Ray Huang

Abstract:

This study compares the syntax and semantics of two kinds of passives in Mandarin Chinese: bèi passives and yóu passives. To express a Chinese equivalent for ‘The thief was taken away by the police,’ either bèi or yóu can be used, as in Xiǎotōu bèi/yóu jǐngchá dàizǒu le. It is shown in this study that bèi passives and yóu passives differ semantically and syntactically. The semantic observations are based on the theta theory, dealing with thematic roles. On the other hand, the syntactic analysis draws heavily upon the generative grammar, looking into thematic structures. The findings of this study are as follows. First, the core semantics of bèi passives is centered on the Patient NP in the subject position. This Patient NP is essentially an Affectee, undergoing the outcome or consequence brought up by the action represented by the predicate. This may explain why in the sentence Wǒde huà bèi/*yóu tā niǔqū le ‘My words have been twisted by him/her,’ only bèi is allowed. This is because the subject NP wǒde huà ‘my words’ suffers a negative consequence. Yóu passives, in contrast, place the semantic focus on the post-yóu NP, which is not an Affectee though. Instead, it plays a role which has to take certain responsibility without being affected in a way like an Affectee. For example, in the sentence Zhèbù diànyǐng yóu/*bèi tā dānrèn dǎoyǎn ‘This film is directed by him/her,’ only the use of yóu is possible because the post-yóu NP tā ‘s/he’ refers to someone in charge, who is not an Affectee, nor is the sentence-initial NP zhèbù diànyǐng ‘this film’. When it comes to the second finding, the syntactic structures of bèi passives and yóu passives differ in that the former involve a two-place predicate while the latter a three-place predicate. The passive morpheme bèi in a case like Xiǎotōu bèi jǐngchá dàizǒu le ‘The thief was taken away by the police’ has been argued by some Chinese syntacticians to be a two-place predicate which selects an Experiencer subject and an Event complement. Under this analysis, the initial NP xiǎotōu ‘the thief’ in the above example is a base-generated subject. This study, however, proposes that yóu passives fall into a three-place unergative structure. In the sentence Xiǎotōu yóu jǐngchá dàizǒu le ‘The thief was taken away by the police,’ the initial NP xiǎotōu ‘the thief’ is a topic which serves as a Patient taken by the verb dàizǒu ‘take away.’ The subject of the sentence is assumed to be an Agent, which is in a null form and may find its reference from the discourse or world knowledge. Regarding the post-yóu NP jǐngchá ‘the police,’ its status is dual. On the one hand, it is a Patient introduced by the light verb yóu; on the other, it is an Agent assigned by the verb dàizǒu ‘take away.’ It is concluded that the findings in this study contribute to better understanding of what makes the distinction between the two kinds of Chinese passives.

Keywords: affectee, passive, patient, unergative

Procedia PDF Downloads 273

Authors: Umar Hayatu Sidik

Abstract:

Application of liquid base petroleum fuel (petrol and diesel) for transportation fuel causes emissions of greenhouse gases (GHGs), while natural gas (NG) reduces the emissions of greenhouse gases (GHGs). At present, compression and liquefaction are the most matured technology used for transportation system. For transportation use, compression requires high pressure (200–300 bar) while liquefaction is impractical. A relatively low pressure of 30-40 bar is achievable by adsorbed natural gas (ANG) to store nearly compressed natural gas (CNG). In this study, adsorbents for high-pressure adsorption of methane (CH4) was prepared from coconut shells and polyetheretherketone (PEEK) using potassium hydroxide (KOH) and microwave-assisted activation. Design expert software version 7.1.6 was used for optimization and prediction of preparation conditions of the adsorbents for CH₄ adsorption. Effects of microwave power, activation time and quantity of PEEK on the adsorbents performance toward CH₄ adsorption was investigated. The adsorbents were characterized by Fourier transform infrared spectroscopy (FTIR), thermogravimetric (TG) and derivative thermogravimetric (DTG) and scanning electron microscopy (SEM). The ideal CH4 adsorption capacities of adsorbents were determined using volumetric method at pressures of 5, 17, and 35 bar at an ambient temperature and 5 oC respectively. Isotherm and kinetics models were used to validate the experimental results. The optimum preparation conditions were found to be 15 wt% amount of PEEK, 3 minutes activation time and 300 W microwave power. The highest CH4 uptake of 9.7045 mmol CH4 adsorbed/g adsorbent was recorded by M33P15 (300 W of microwave power, 3 min activation time and 15 wt% amount of PEEK) among the sorbents at an ambient temperature and 35 bar. The CH4 equilibrium data is well correlated with Sips, Toth, Freundlich and Langmuir. Isotherms revealed that the Sips isotherm has the best fit, while the kinetics studies revealed that the pseudo-second-order kinetic model best describes the adsorption process. In all scenarios studied, a decrease in temperature led to an increase in adsorption of both gases. The adsorbent (M33P15) maintained its stability even after seven adsorption/desorption cycles. The findings revealed the potential of coconut shell-PEEK as CH₄ adsorbents.

Keywords: adsorption, desorption, activated carbon, coconut shells, polyetheretherketone

Procedia PDF Downloads 67

Authors: Wanjiku Karanja

Abstract:

Facebook has monopoly power in the social networking market. It has grown and entrenched its monopoly power through the capture of its users’ data value chains. However, antitrust law’s consumer welfare roots have prevented it from effectively addressing the role of data capture in Facebook’s market dominance. These regulatory blind spots are augmented in Facebook’s proposed Diem cryptocurrency project and its Novi Digital wallet. Novi, which is Diem’s digital identity component, shall enable Facebook to collect an unprecedented volume of consumer data. Consequently, Novi has seismic implications on internet identity as the network effects of Facebook’s large user base could establish it as the de facto internet identity layer. Moreover, the large tracts of data Facebook shall collect through Novi shall further entrench Facebook's market power. As such, the attendant lock-in effects of this project shall be very difficult to reverse. Urgent regulatory action is therefore required to prevent this expansion of Facebook’s data resources and monopoly power. This research thus highlights the importance of data capture to competition and market health in the social networking industry. It utilizes interviews with key experts to empirically interrogate the impact of Facebook’s data capture and control of its users’ data value chains on its market power. This inquiry is contextualized against Novi’s expansive effect on Facebook’s data value chains. It thus addresses the novel antitrust issues arising at the nexus of Facebook’s monopoly power and the privacy of its users’ data. It also explores the impact of platform design principles, specifically data portability and data portability, in mitigating Facebook’s anti-competitive practices. As such, this study finds that Facebook is a powerful monopoly that dominates the social media industry to the detriment of potential competitors. Facebook derives its power from its size, annexure of the consumer data value chain, and control of its users’ social graphs. Additionally, the platform design principles of data interoperability and data portability are not a panacea to restoring competition in the social networking market. Their success depends on the establishment of robust technical standards and regulatory frameworks.

Keywords: antitrust law, data protection law, data portability, data interoperability, digital identity, Facebook

Procedia PDF Downloads 123

Authors: Nizar Chaira

Abstract:

Dates, main products of the oases, due to their therapeutic interests, are considered highly nutritious fruit. Several studies on the valuation biotechnology and technology of dates are made, and several products are already prepared. Isolation of the yeast Saccharomyces cerevisiae, naturally presents in a scrap of date, optimization of growth in the medium based on date syrup and production biomass can potentially expand the range of secondary products of dates. To this end, this paper tries to study the suitability for processing dates technology and biotechnology to use the date pulp as a carbon source for biological transformation. Two strains of Saccharomyces cerevisiae isolated from date syrup (S1, S2) and a commercial strain have used for this study. After optimization of culture conditions, production in a fermenter on two different media (date syrup and beet molasses) was performed. This is followed by studying the kinetics of growth, protein production and consumption of sugars in crops strain 1, 2 and the commercial strain and on both media. The results obtained showed that a concentration of 2% sugar, 2.5 g/l yeast extract, pH 4.5 and a temperature between 25 and 35°C are the optimal conditions for cultivation in a bioreactor. The exponential phase of the specific growth rate of a strain on both media showed that it is about 0.3625 h-1 for the production of a medium based on date syrup and 0.3521 h-1 on beet molasses with a generation time equal to 1.912 h and on the medium based on date syrup, yeast consumes preferentially the reducing sugars. For the production of protein, we showed that this latter presents an exponential phase when the medium starts to run out of reducing sugars. For strain 2, the specific growth rate is about 0.261h-1 for the production on a medium based on date syrup and 0207 h-1 on beet molasses and the base medium syrup date of the yeast consumes preferentially reducing sugars. For the invertase and other metabolits, these increases rapidly after exhaustion of reducing sugars. The comparison of productivity between the three strains on the medium based on date syrup showed that the maximum value is obtained with the second strain: p = 1072 g/l/h as it is about of 0923 g/l/h for strain 1 and 0644 g/l/h for the commercial strain. Thus, isolates of date syrup are more competitive than the commercial strain and can give the same performance in a shorter time with energy gain.

Keywords: date palm, fermentation, molasses, Saccharomyces, syrup

Procedia PDF Downloads 321

Authors: Gashaw Gismu Chakilu

Abstract:

Climate and land cover change are very important issues in terms of global context and their responses to environmental and socio-economic drivers. The dynamic of these two factors is currently affecting the environment in unbalanced way including watershed hydrology. In this paper individual and combined impacts of climate change and land use land cover change on hydrological processes were evaluated through applying the model Soil and Water Assessment Tool (SWAT) in Gumara watershed, Upper Blue Nile basin Ethiopia. The regional climate; temperature and rainfall data of the past 40 years in the study area were prepared and changes were detected by using trend analysis applying Mann-Kendall trend test. The land use land cover data were obtained from land sat image and processed by ERDAS IMAGIN 2010 software. Three land use land cover data; 1973, 1986, and 2013 were prepared and these data were used for base line, model calibration and change study respectively. The effects of these changes on high flow and low flow of the catchment have also been evaluated separately. The high flow of the catchment for these two decades was analyzed by using Annual Maximum (AM) model and the low flow was evaluated by seven day sustained low flow model. Both temperature and rainfall showed increasing trend; and then the extent of changes were evaluated in terms of monthly bases by using two decadal time periods; 1973-1982 was taken as baseline and 2004-2013 was used as change study. The efficiency of the model was determined by Nash-Sutcliffe (NS) and Relative Volume error (RVe) and their values were 0.65 and 0.032 for calibration and 0.62 and 0.0051 for validation respectively. The impact of climate change was higher than that of land use land cover change on stream flow of the catchment; the flow has been increasing by 16.86% and 7.25% due to climate and LULC change respectively, and the combined change effect accounted 22.13% flow increment. The overall results of the study indicated that Climate change is more responsible for high flow than low flow; and reversely the land use land cover change showed more significant effect on low flow than high flow of the catchment. From the result we conclude that the hydrology of the catchment has been altered because of changes of climate and land cover of the study area.

Keywords: climate, LULC, SWAT, Ethiopia

Procedia PDF Downloads 375

Authors: Alexander Rych

Abstract:

Piql Preservation Services (“Piql”) is a turnkey solution designed for secure, migration-free long- term preservation of digital data. Piql sets an open standard for long- term preservation for the future. It consists of equipment and processes needed for writing and retrieving digital data. Exponentially growing amounts of data demand for logistically effective and cost effective processes. Digital storage media (hard disks, magnetic tape) exhibit limited lifetime. Repetitive data migration to overcome rapid obsolescence of hardware and software bears accelerated risk of data loss, data corruption or even manipulation and adds significant repetitive costs for hardware and software investments. Piql stores any kind of data in its digital as well as analog form securely for 500 years. The medium that provides this is a film reel. Using photosensitive film polyester base, a very stable material that is known for its immutability over hundreds of years, secure and cost-effective long- term preservation can be provided. The film reel itself is stored in a packaging capable of protecting the optical storage medium. These components have undergone extensive testing to ensure longevity of up to 500 years. In addition to its durability, film is a true WORM (write once- read many) medium. It therefore is resistant to editing or manipulation. Being able to store any form of data onto the film makes Piql a superior solution for long-term preservation. Paper documents, images, video or audio sequences – all of those file formats and documents can be preserved in its native file structure. In order to restore the encoded digital data, only a film scanner, a digital camera or any appropriate optical reading device will be needed in the future. Every film reel includes an index section describing the data saved on the film. It also contains a content section carrying meta-data, enabling users in the future to rebuild software in order to read and decode the digital information.

Keywords: digital data, long-term preservation, migration-free, photosensitive film

Procedia PDF Downloads 392

Authors: Elizabeth Loza-Valerdi, Victor Pardiñas-Rios, Arnulfo Pluma-Pluma, Andres Breton-Toral, Julio Cercado-Jaramillo

Abstract:

The purification processes for mixtures of isomeric monosaccharides using industrial chromatographic methods poses a serious technical challenge. Mixtures of 2 or 3 monosaccharides are difficult to separate by strictly physical or chemical techniques. Differential fermentation by microbial cultures is an increasingly interesting way of selective enrichment in a particular kind of monosaccharides when a mixture of them is present in the solution, and only one has economical value. Osmotolerant yeast cultures provide an interesting source of biocatalysts for the selective catabolism of monosaccharides in media containing high concentrations of total soluble sugars. A collection of 398 yeast strains has been obtained using endemic and unique sources of fruit juices, industrial syrups, honey, and other high sugar content substrates, either natural or man made, products and by-products from Mexico. The osmotolerance of the strains was assessed by plate assay both in glucose (20-40-60%w/w). Strains were classified according to their osmotolerance in low, medium or highly tolerant to high glucose concentrations. The purified cultures were tested by their ability to growth in a solid plate media or liquid media of Yeas Nitrogen Base (YNB), added with specific monosaccharides as sole carbon source (glucose, galactose, lactose and fructose). Selected strains were subsequently tested in fermentation experiments with mixtures of two monosaccharides (galactose/glucose and glucose/fructose). Their ability to grow and selectively catabolize one monosaccharide was evaluated. Growth, fermentation activity and products of metabolism were determined by plate counts, CO2 production, turbidity and chromatographic analysis by HPLC. Selective catabolism of one monosaccharide in liquid media containing two monosaccharides was confirmed for 8 strains. Ion Exchange chromatographic processes were used in production of high fructose or galactose syrup. Laboratory scale processes for the production of fructose or galactose enriched syrups is now feasible, with important applications in food (like high fructose syrup as edulcorant) and fermentation technology (for GOS production).

Keywords: osmotolerant yeasts, selective metabolism, fructose syrup, GOS

Procedia PDF Downloads 449

Authors: Ujjawal Kumar Bhagat, Kamaluddin, Rama Krishna Peddinti

Abstract:

The Huisgen’s 1,3-dipolar [3+2] cycloaddition of organic azides and alkynes often give the mixtures of both the regioisomers 1,4- and 1,5- disubstituted 1,2,3-triazoles. Later, in presence of metal salts (click chemistry) such as copper(I)-catalyzed azide-alkyne cycloaddition (CuAAC) was used for the synthesis of 1,4-disubstituted 1,2,3-triazoles as a sole products regioselectively. Also, the ‘click reactions’ of Ruthenium-catalyzed azides-alkynes cycloaddition (RuAAC) is used for the synthesis of 1,5-disubstituted 1,2,3-triazoles as a single isomer. The synthesis of 1,4- and 1.5-disubstituted 1,2,3-triazoles has become the gold standard of ‘click chemistry’ due to its reliability, specificity, and biocompatibility. The 1,4- and 1,5-disubstituted 1,2,3-triazoles have emerged as one of the most powerful entities in the varieties of biological properties like antibacterial, antitubercular, antitumor, antifungal and antiprotozoal activities. Some of the 1,4,5-trisubstituted 1,2,3-triazoles exhibit Hsp90 inhibiting properties. The 1,4-disubstituted 1,2,3-triazoles also play a big role in the area of material sciences. The triazole-derived oligomeric, polymeric structures are the potential materials for the preparation of organic optoelectronics, silicon elastomers and unimolecular block copolymers. By the virtue of hydrogen bonding and dipole interactions, the 1,2,3-triazole moiety readily associates with the biological targets. Since, the 4-aryl-1H-1,2,3-triazoles are stable entities, they are chemically robust and very less reactive. In this regard, the addition of 4-aryl-1H-1,2,3-triazoles as nucleophiles to α,β-unsaturated carbonyls and nucleophilic substitution with the epoxides constitutes a powerful and challenging synthetic approach for the generation of disubstituted 1,2,3-triazoles. Herein, we have developed aza-Michael addition of 4-aryl-1H-1,2,3-triazoles to 2-cycloalken-1-ones in the presence of an organic base (DABCO) in acetonotrile solvent leading to the formation of disubstituted 1,2,3-triazoles. The reaction provides 1,4-disubstituted triazoles, 3-(4-aryl-1H-1,2,3-triazol-1-yl)cycloalkanones in major amount along with 1,5-disubstituted 1,2,3-triazoles, minor regioisomers with excellent combined chemical yields (upto99%). The nucleophilic behavior of 4-aryl-1H-1,2,3-triazoles was also tested in the ring opening of meso-epoxides in the presence of organic bases (DABCO/Et3N) in acetonotrile solvent furnishing the two regioisomers1,4- and 1,5-disubstituted 1,2,3-triazoles. Thus, the novelty of this methodology is synthesis of diversified disubstituted 1,2,3-triazoles under metal free condition.The results will be presented in detail.

Keywords: aza-Michael addition, cycloalkenones, epoxides, triazoles

Procedia PDF Downloads 322

Authors: Mariya Dayana, Budhmal Jain

Abstract:

Kannur International Airport Ltd. (KIAL) is a new Greenfield airport project with airside development on an undulating terrain with an average height of 90m above Mean Sea Level (MSL) and a maximum height of 142m. To accommodate the desired Runway length and Runway End Safety Area (RESA) at both the ends along the proposed alignment, it resulted in 45.5 million cubic meters in cutting and filling. The insufficient availability of land for the construction of free slope embankment at RESA 07 end resulted in the design and construction of Reinforced Soil Slope (RSS) with a maximum slope of 65 degrees. An embankment fill of average 70m height with steep slopes located in high rainfall area is a unique feature of this project. The design and construction was challenging being asymmetrical with curves and bends. The fill was reinforced with high strength Uniaxial geogrids laid perpendicular to the slope. Weld mesh wrapped with coir mat acted as the facia units to protect it against surface failure. Face anchorage were also provided by wrapping the geogrids along the facia units where the slope angle was steeper than 45 degrees. Considering high rainfall received on this table top airport site, extensive drainage system was designed for the high embankment fill. Gabion wall up to 10m height were also designed and constructed along the boundary to accommodate the toe of the RSS fill beside the jeepable track at the base level. The design of RSS fill was done using ReSSA software and verified in PLAXIS 2D modeling. Both slip surface failure and wedge failure cases were considered in static and seismic analysis for local and global failure cases. The site won excavated laterite soil was used as the fill material for the construction. Extensive field and laboratory tests were conducted during the construction of RSS system for quality assurance. This paper represents a case study detailing the design and construction of a very high embankment using geosynthetics for the provision of Runway length and RESA area.

Keywords: airport, embankment, gabion, high strength uniaxial geogrid, kial, laterite soil, plaxis 2d

Procedia PDF Downloads 162

Authors: Ifigeneia V. Mavragani, Zacharenia Nikitaki, George Kalantzis, George Iliakis, Alexandros G. Georgakilas

Abstract:

Complex DNA damage consisting of a combination of DNA lesions, such as Double Strand Breaks (DSBs) and non-DSB base lesions occurring in a small volume is considered as one of the most important biological endpoints regarding ionizing radiation (IR) exposure. Strong theoretical (Monte Carlo simulations) and experimental evidence suggests an increment of the complexity of DNA damage and therefore repair resistance with increasing linear energy transfer (LET). Experimental detection of complex (clustered) DNA damage is often associated with technical deficiencies limiting its measurement, especially in cellular or tissue systems. Our groups have recently made significant improvements towards the identification of key parameters relating to the efficient detection of complex DSBs and non-DSBs in human cellular systems exposed to IR of varying quality (γ-, X-rays 0.3-1 keV/μm, α-particles 116 keV/μm and 36Ar ions 270 keV/μm). The induction and processing of DSB and non-DSB-oxidative clusters were measured using adaptations of immunofluorescence (γH2AX or 53PB1 foci staining as DSB probes and human repair enzymes OGG1 or APE1 as probes for oxidized purines and abasic sites respectively). In the current study, Relative Biological Effectiveness (RBE) values for DSB and non-DSB induction have been measured in different human normal (FEP18-11-T1) and cancerous cell lines (MCF7, HepG2, A549, MO59K/J). The experimental results are compared to simulation data obtained using a validated microdosimetric fast Monte Carlo DNA Damage Simulation code (MCDS). Moreover, this simulation approach is implemented in two realistic clinical cases, i.e. prostate cancer treatment using X-rays generated by a linear accelerator and a pediatric osteosarcoma case using a 200.6 MeV proton pencil beam. RBE values for complex DNA damage induction are calculated for the tumor areas. These results reveal a disparity between theory and experiment and underline the necessity for implementing highly precise and more efficient experimental and simulation approaches.

Keywords: complex DNA damage, DNA damage simulation, protons, radiotherapy

Procedia PDF Downloads 325

Authors: Kai-Shiang Chang, Shiao-Shing Chen, Saikat Sinha Ray, Hung-Te Hsu

Abstract:

In recent years, membrane bioreactors (MBR) have been widely utilized as it can effectively replace conventional activated sludge process (CAS). Membrane bioreactor (MBR) is found to be more effective technology compared to other conventional activated sludge process and advanced membrane separation technique. Additionally, as far as the MBR is concerned, it is having excellent control of sludge retention time (SRT) and hydraulic retention time (HRT) and conducive to the retention of high concentration of sludge biomass. The membrane bioreactor (MBR) can effectively reduce footprint in terms of area and omit the secondary processing procedures in the conventional activated sludge process (CAS). Currently, as per the membrane technology, the ceramic membrane is found to have highly strong anti-acid-base properties, and it is more suitable than polymeric membrane while using for backwash and chemical cleaning. This study is based upon the treatment of Cutting Fluid wastewater, as the Cutting Fluid is widely used in the cutting equipment. However, the Cutting Fluid wastewater is very difficult to treat. In this study, the ceramic membrane was used and combine with of MBR system to treat the Cutting Fluid wastewater. In this present study, different kind of chemical coagulants have been utilized for pretreatment purpose in order to get the supernatant and simultaneously this wastewater (supernatant) was treated by MBR process. Nevertheless, ceramic membrane has three advantages such as high mechanical strength, drug resistance and reuse. During the experiment, the backwash technique was used for every interval of 10 minutes in order to avoid fouling of the membrane. In this study, during pretreatment the Chemical Oxygen Demand (COD) removal efficiency was found to be 71-86% and oil removal efficiency was analyzed to be 83-92%. This pretreatment study suggests that it is quiet effective methodology to reduce COD and oil concentration. Finally, In the MBR system when the HRT is more than 7.5 hour, the COD removal efficiency was found to be 87-93% and could achieve 100% oil removal efficiency. Coagulation test series were seen in Refs coagulants for the treatment of wastewater containing cutting oil with better oil and COD removal efficiency. The results also showed that the oil removal efficiency in the MBR system could reduce the oil content to less than 1 mg / L when the oil quality was 126 mg / L. Therefore, in this paper, the performance of membrane bioreactor by utilizing ceramic membrane has been demonstrated for treatment of Cutting Fluid wastewater.

Keywords: membrane bioreactor, cutting fluid, oil, chemical oxygen demand

Procedia PDF Downloads 314

Authors: Geun-Yeon Kim, S. P. Praveen Kumar, Kwon-Hee Lee

Abstract:

A steering knuckle arm is the component that connects the steering system and suspension system. The structural performances such as stiffness, strength, and durability are considered in its design process. The former study suggested the lightweight design of a knuckle arm considering the structural performances and using the metamodel-based optimization. The six shape design variables were defined, and the optimum design was calculated by applying the kriging interpolation method. The finite element method was utilized to predict the structural responses. The suggested knuckle was made of the aluminum Al6082, and its weight was reduced about 60% in comparison with the base steel knuckle, satisfying the design requirements. Then, we investigated its manufacturability by performing foraging analysis. The forging was done as hot process, and the product was made through two-step forging. As a final step of its developing process, the durability is investigated by using the flexible dynamic analysis software, LS-DYNA and the pre and post processor, eta/VPG. Generally, a car make does not provide all the information with the part manufacturer. Thus, the part manufacturer has a limit in predicting the durability performance with the unit of full car. The eta/VPG has the libraries of suspension, tire, and road, which are commonly used parts. That makes a full car modeling. First, the full car is modeled by referencing the following information; Overall Length: 3,595mm, Overall Width: 1,595mm, CVW (Curve Vehicle Weight): 910kg, Front Suspension: MacPherson Strut, Rear Suspension: Torsion Beam Axle, Tire: 235/65R17. Second, the road is selected as the cobblestone. The road condition of the cobblestone is almost 10 times more severe than that of usual paved road. Third, the dynamic finite element analysis using the LS-DYNA is performed to predict the durability performance of the suggested knuckle arm. The life of the suggested knuckle arm is calculated as 350,000km, which satisfies the design requirement set up by the part manufacturer. In this study, the overall design process of a knuckle arm is suggested, and it can be seen that the developed knuckle arm satisfies the design requirement of the durability with the unit of full car. The VPG analysis is successfully performed even though it does not an exact prediction since the full car model is very rough one. Thus, this approach can be used effectively when the detail to full car is not given.

Keywords: knuckle arm, structural optimization, Metamodel, forging, durability, VPG (Virtual Proving Ground)

Procedia PDF Downloads 419

Authors: Elham Azimzadeh, Saeedeh Sepehri, Hamidollah Hassanlouei

Abstract:

Obesity is associated with postural instability, might influence the quality of daily life, and could be considered a potential factor for falling in obese people. The fat body mass especially in the abdominal area may increase body sway. Furthermore, loss of visual feedback may induce a larger postural sway in obese people. Moreover, Muscle fatigue may impair the work capacity of the skeletal muscle and may alter joint proprioception. So, the purpose of this study was to investigate the effect of physical fatigue and visual feedback on body sway and strength of lower extremities in obese people. 12 obese (4 female, 8 male; BMI >30 kg/m2), and 12 normal weight (4 female, 8 male; BMI: 20-25 kg/m2) subjects aged 37- 47 years participated in this study. The postural stability test on the Biodex balance system was used to characterize postural control along the anterior-posterior (AP) and mediolateral (ML) directions in eyes open and eyes closed conditions and maximal voluntary contraction (MVC) of knee extensors and flexors were measured before and after the high-intensity exhausting exercise protocol on the ergometer bike to confirm the presence of fatigue. Results indicated that the obese group demonstrated significantly greater body sway, in all indices (ML, AP, overall) compared with the normal weight group (eyes open). However, when visual feedback was eliminated, fatigue impaired the balance in the overall and AP indicators in both groups; ML sway was higher only in the obese group after exerting the fatigue in the eyes closed condition. Also, maximal voluntary contraction of knee extensors was impaired in the fatigued normal group but, there was no significant impairment in knee flexors MVC in both group. According to the findings, peripheral fatigue was associated with altered postural control in upright standing when eyes were closed, and that mechanoreceptors of the feet may be less able to estimate the position of the body COM over the base of support in the loss of visual feedback. This suggests that the overall capability of the postural control system during upright standing especially in the ML direction could be lower due to fatigue in obese individuals and could be a predictor of future falls.

Keywords: maximal voluntary contraction, obesity, peripheral fatigue, postural control, visual feedback

Procedia PDF Downloads 92

Authors: Mohd Harun, Cini Varghese, Eldho Varghese, Seema Jaggi

Abstract:

Hybridization crosses find a vital role in breeding experiments to evaluate the combining abilities of individual parental lines or crosses for creation of lines with desirable qualities. There are various ways of obtaining progenies and further studying the combining ability effects of the lines taken in a breeding programme. Some of the most common methods are diallel or two-way cross, triallel or three-way cross, tetra-allele or four-way cross. These techniques help the breeders to improve the quantitative traits which are of economical as well as nutritional importance in crops and animals. Amongst these methods, tetra-allele cross provides extra information in terms of the higher specific combining ability (sca) effects and the hybrids thus produced exhibit individual as well as population buffering mechanism because of the broad genetic base. Most of the common commercial hybrids in corn are either three-way or four-way cross hybrids. Tetra-allele cross came out as the most practical and acceptable scheme for the production of slaughter pigs having fast growth rate, good feed efficiency, and carcass quality. Tetra-allele crosses are mostly used for exploitation of heterosis in case of commercial silkworm production. Experimental designs involving tetra-allele crosses have been studied extensively in literature. Optimality of designs has also been considered as a researchable issue. In practical situations, it is advisable to include sca effects in the model as this information is needed by the breeder to improve economically and nutritionally important quantitative traits. Thus, a model that provides information regarding the specific traits by utilizing sca effects along with general combining ability (gca) effects may help the breeders to deal with the problem of various stresses. In this paper, a model for experimental designs involving tetra-allele crosses that incorporates both gca and sca has been defined. Optimality aspects of such designs have been discussed incorporating sca effects in the model. Orthogonality conditions have been derived for block designs ensuring estimation of contrasts among the gca effects, after eliminating the nuisance factors, independently from sca effects. User friendly SAS macro and web solution (webPTC) have been developed for the generation and analysis of such designs.

Keywords: general combining ability, optimality, specific combining ability, tetra-allele cross, webPTC

Procedia PDF Downloads 137

Authors: Para Jansuwan, Kerstin K. Zander

Abstract:

Most people in rural Thailand still depend on agriculture. The rural areas are undergoing changes in their demographic structures with an increasing older population, out migration of younger people and a shift away from work in the agricultural sector towards manufacturing and service provisioning. These changes may lead to a decline in agricultural productivity and food insecurity. Our research aims to examine perceptions of older farmers on how rural demographic change affects them, to investigate how farmers may change their agricultural practices to cope with their ageing and to explore the factors affecting these changes, including the opportunities and challenges arising from them. The data were collected through a household survey with 368 farmers in the Prachin Buri province in central Thailand, the main area for agricultural production. A series of binomial logistic regression models were applied to analyse the data. We found that most farmers suffered from age-related diseases, which compromised their working capacity. Most farmers attempted to reduce labour intense work, by either stopping farming through transferring farmland to their children (41%), stopping farming by giving the land to the others (e.g., selling, leasing out) (28%) and continuing farming with making some changes (e.g., changing crops, employing additional workers) (24%). Farmers’ health and having a potential farm successor were positively associated with the probability of stopping farming by transferring the land to the children. Farmers with a successor were also less likely to stop farming by giving the land to the others. Farmers’ age was negatively associated with the likelihood of continuing farming by making some changes. The results show that most farmers base their decisions on the hope that their children will take over the farms, and that without successor, farmers lease out or sell the land. Without successor, they also no longer invest in expansion and improvement of their farm production, especially adoption of innovative technologies that could help them to maintain their farm productivity. To improve farmers’ quality of life and sustain their farm productivity, policies are needed to support the viability of farms, the access to a pension system and the smooth and successful transfer of the land to a successor of farmers.

Keywords: rural demographic change, older farmer, stopping farming, continuing farming, health and age, farm successor, Thailand

Procedia PDF Downloads 114

Authors: Tawfig Alghbaili

Abstract:

LP3D Field is located near the center of the Sirt Basin in the Marada Trough approximately 215 km south Marsa Al Braga City. The Marada Trough is bounded on the west by a major fault, which forms the edge of the Beda Platform, while on the east, a bounding fault marks the edge of the Zelten Platform. The main reservoir in the LP3D Field is Upper Paleocene Beda Formation. The Beda Formation is mainly limestone interbedded with shale. The reservoir average thickness is 117.5 feet. To develop a better understanding of the characterization and distribution of the Beda reservoir, quantitative seismic data interpretation has been done, and also, well logs data were analyzed. Six reflectors corresponding to the tops of the Beda, Hagfa Shale, Gir, Kheir Shale, Khalifa Shale, and Zelten Formations were picked and mapped. Special work was done on fault interpretation part because of the complexities of the faults at the structure area. Different attribute analyses were done to build up more understanding of structures lateral extension and to view a clear image of the fault blocks. Time to depth conversion was computed using velocity modeling generated from check shot and sonic data. The simplified stratigraphic cross-section was drawn through the wells A1, A2, A3, and A4-LP3D. The distribution and the thickness variations of the Beda reservoir along the study area had been demonstrating. Petrophysical analysis of wireline logging also was done and Cross plots of some petrophysical parameters are generated to evaluate the lithology of reservoir interval. Structure and Stratigraphic Framework was designed and run to generate different model like faults, facies, and petrophysical models and calculate the reservoir volumetric. This study concluded that the depth structure map of the Beda formation shows the main structure in the area of study, which is north to south faulted anticline. Based on the Beda reservoir models, volumetric for the base case has been calculated and it has STOIIP of 41MMSTB and Recoverable oil of 10MMSTB. Seismic attributes confirm the structure trend and build a better understanding of the fault system in the area.

Keywords: LP3D Field, Beda Formation, reservoir models, Seismic attributes

Procedia PDF Downloads 214

Authors: Kym Drady

Abstract:

This paper considers whether creativity is the missing link which would allow the evolution of organisational behaviour and profitability if it was ‘released’. It suggests that although many organisations try to engage their workforce and expect innovation they fail to provide the means for its achievement. The paper suggests that creative thinking is the ‘glue’ which links organisational performance to profitability. A key role of a university today, is to produce skilled and capable graduates. Increasing competition and internationalisation has meant that the employability agenda has never been more prominent within the field of education. As such it should be a key consideration when designing and developing a curriculum. It has been suggested that creativity is a valuable personal skill and perhaps should be the focus of an organisations business strategy in order for them to increase their competitive advantage in the twenty first century. Flexible and agile graduates are now required to become creative in their use of skills and resources in an increasingly complex and sophisticated global market. The paper, therefore, questions that if this is the case why then does creativity fail to appear as a key curriculum subject in many business schools. It also considers why policy makers continue to neglect this critical issue when it could offer the ‘key’ to economic prosperity. Recent literature does go some way to addressing by suggesting that small clusters of UK Universities have started including some creativity in their PDP work. However, this paper builds on this work and proposes that that creativity should become a central component of the curriculum. The paper suggests that creativity should appear in every area of the curriculum and that it should act as the link that connects productivity to profitability rather than being marginalised as an additional part of the curriculum. A range of data gathering methods have been used but each has been drawn from a qualitative base as it was felt that due to nature of the study individual’s thoughts and feelings needed to be examined and reflection was important. The author also recognises the importance of her own reflection both on the experiences of the students and their later working experiences as well as on the creative elements within the programme that she delivered. This paper has been drawn from research undertaken by the author in relation to her PhD study which explores the potential benefits of including creativity in the curriculum within business schools and the added value this could make to their employability. To conclude, creativity is, in the opinion of the author, the missing link to organisational profitability and as such should be prioritised especially by higher education providers.

Keywords: business curriculum, business curriculum, higher education, creative thinking and problem-solving, creativity

Procedia PDF Downloads 274

Authors: Konstantina Georgali

Abstract:

The present study explores Greek teachers’ understandings of typical language development and of language difficulties. Its core aim was to highlight that teachers need to have a thorough understanding of educational linguistics, that is of how language figures in education. They should also be aware of how language should be taught so as to promote language development for all students while at the same time support the needs of children with language difficulties in an inclusive ethos. The study, thus argued that language can be a dynamic learning mechanism in the minds of all children and a powerful teaching tool in the hands of teachers and provided current research evidence to show that structural and morphological particularities of native languages- in this case, of the Greek language- can be used by teachers to enhance children’s understanding of language and simultaneously improve oral language skills for children with typical language development and for those with language difficulties. The research was based on a Sequential Exploratory Mixed Methods Design deployed in three consecutive and integrative phases. The first phase involved 18 exploratory interviews with teachers. Its findings informed the second phase involving a questionnaire survey with 119 respondents. Contradictory questionnaire results were further investigated in a third phase employing a formal testing procedure with 60 children attending Y1, Y2 and Y3 of primary school (a research group of 30 language impaired children and a comparison group of 30 children with typical language development, both identified by their class teachers). Results showed both strengths and weaknesses in teachers’ awareness of educational linguistics and of language difficulties. They also provided a different perspective of children’s language needs and of language teaching approaches that reflected current advances and conceptualizations of language problems and opened a new window on how best they can be met in an inclusive ethos. However, teachers barely used teaching approaches that could capitalize on the particularities of the Greek language to improve language skills for all students in class. Although they seemed to realize the importance of oral language skills and their knowledge base on language related issues was adequate, their practices indicated that they did not see language as a dynamic teaching and learning mechanism that can promote children’s language development and in tandem, improve academic attainment. Important educational implications arose and clear indications of the generalization of findings beyond the Greek educational context.

Keywords: educational linguistics, inclusive ethos, language difficulties, typical language development

Procedia PDF Downloads 382

Authors: Iman Farasat, Howard M. Salis

Abstract:

The CRISPR/Cas9 system has revolutionized genome engineering by enabling site-directed and high-throughput genome editing, genome insertion, and gene knockdowns in several species, including bacteria, yeast, flies, worms, and human cell lines. This technology has the potential to enable human gene therapy to treat genetic diseases and cancer at the molecular level; however, the current CRISPR/Cas9 system suffers from seemingly sporadic off-target genome mutagenesis that prevents its use in gene therapy. A comprehensive mechanistic model that explains how the CRISPR/Cas9 functions would enable the rational design of the guide-RNAs responsible for target site selection while minimizing unexpected genome mutagenesis. Here, we present the first quantitative model of the CRISPR/Cas9 genome mutagenesis system that predicts how guide-RNA sequences (crRNAs) control target site selection and cleavage activity. We used statistical thermodynamics and law of mass action to develop a five-step biophysical model of cas9 cleavage, and examined it in vivo and in vitro. To predict a crRNA's binding specificities and cleavage rates, we then compiled a nearest neighbor (NN) energy model that accounts for all possible base pairings and mismatches between the crRNA and the possible genomic DNA sites. These calculations correctly predicted crRNA specificity across 5518 sites. Our analysis reveals that cas9 activity and specificity are anti-correlated, and, the trade-off between them is the determining factor in performing an RNA-mediated cleavage with minimal off-targets. To find an optimal solution, we first created a scheme of safe-design criteria for Cas9 target selection by systematic analysis of available high throughput measurements. We then used our biophysical model to determine the optimal Cas9 expression levels and timing that maximizes on-target cleavage and minimizes off-target activity. We successfully applied this approach in bacterial and mammalian cell lines to reduce off-target activity to near background mutagenesis level while maintaining high on-target cleavage rate.

Keywords: biophysical model, CRISPR, Cas9, genome editing

Procedia PDF Downloads 406

Authors: Amanda Aliende da Matta

Abstract:

In different fields, there are people who have something that stands out. In the educational world, for example, it is clear when some teachers have something: they are the best teachers, but this is not directly attributed to their disciplines, methodologies, etc. It is that they have something that captivates, inspires, and motivates. But we also find this something in other contexts. In this thesis, the interest is in something that some marginalized people, such as Ab (fictitious name), have. Ab was born in a rural community and saw the lifestyle of his family change drastically as a consequence of structural changes in his village. The community became impoverished, and together with a group of teenagers, he decided to migrate to Spain in search of opportunities. His best friend drowned during the crossing. After arriving, he lived in indecent conditions and felt unsafe. He now suffers from anxiety and frequently faints from it. Yet, he’s linked to Joves x la pau (a Christian project, although he is a Muslim), distributing food for people who live on the streets every Thursday afternoon. When he asked about what happens on cold and rainy days, he explained simply: "if it rains, I distribute the food, and immediately I get home, take a bath, and sleep warm under my roof. That is when we most have to go." This something he has will be called caring. And one of the general objectives of the thesis is to discover what are the meaning structures of this caring what is the lived experience of this caring. In this communication, preliminary results of an Applied Hermeneutic Phenomenology (AHP) study on the lived experience of caring as a vulnerable person are presented. The research means to answer what is the lived experience of caring as a vulnerable person. That is, to describe and explain what it is like to caregive for a vulnerable person, what it is, essentially, to caregive for a vulnerable person, what makes the lived experience of caregiving for a vulnerable person different from any other. In order to investigate the meaning of the phenomenon of caregiving as a vulnerable person, as already stated, the method used will be Applied Hermeneutic Phenomenology (AHP). We base ourselves, initially, on the proposal of Raquel Ayala-Carabajo and Max Van Manen. As Van Manen (1990) explains, AHP is a method that works essentially through fieldwork, with the collection of data on lived experience (experiential material). It is a phenomenology of practice. We here present the provisional themes we found: caregiving as a vulnerable person is seeing yourself in the other, identifying with the care-receiver; Caregiving as a vulnerable person is putting the other’s need before oneself’s; Caregiving as a vulnerable person is temporarily overcoming your weaknesses to make yourself strong for the other; Caregiving as a vulnerable person is going beyond the conventional approach; and Caregiving as a vulnerable person is taking responsibility even if it’s not yours.

Keywords: applied hermeneutic phenomenology, care ethics, hermeneutics, phenomenology

Procedia PDF Downloads 92

Authors: Joshua Buli, David Pietrowski, Samuel Britton

Abstract:

Processing SAR data usually requires constraints in extent in the Fourier domain as well as approximations and interpolations onto a planar surface to form an exploitable image. This results in a potential loss of data requires several interpolative techniques, and restricts visualization to two-dimensional plane imagery. The data can be interpolated into a ground plane projection, with or without terrain as a component, all to better view SAR data in an image domain comparable to what a human would view, to ease interpretation. An alternate but computationally heavy method to make use of more of the data is the basis of this research. Pre-processing of the SAR data is completed first (matched-filtering, motion compensation, etc.), the data is then range compressed, and lastly, the contribution from each pulse is determined for each specific point in space by searching the time history data for the reflectivity values for each pulse summed over the entire collection. This results in a per-3D-point reflectivity using the entire collection domain. New advances in GPU processing have finally allowed this rapid projection of acquired SAR data onto any desired reference surface (called backprojection). Mathematically, the computations are fast and easy to implement, despite limitations in SAR phase history data size and 3D-point cloud size. Backprojection processing algorithms are embarrassingly parallel since each 3D point in the scene has the same reflectivity calculation applied for all pulses, independent of all other 3D points and pulse data under consideration. Therefore, given the simplicity of the single backprojection calculation, the work can be spread across thousands of GPU threads allowing for accurate reflectivity representation of a scene. Furthermore, because reflectivity values are associated with individual three-dimensional points, a plane is no longer the sole permissible mapping base; a digital elevation model or even a cloud of points (collected from any sensor capable of measuring ground topography) can be used as a basis for the backprojection technique. This technique minimizes any interpolations and modifications of the raw data, maintaining maximum data integrity. This innovative processing will allow for SAR data to be rapidly brought into a common reference frame for immediate exploitation and data fusion with other three-dimensional data and representations.

Keywords: backprojection, data fusion, exploitation, three-dimensional, visualization

Procedia PDF Downloads 85

Authors: Jean Ross

Abstract:

Rural nursing is not an identified professional identity in the UK, unlike the USA, Canada, and Australia which recognizes rural nursing as a specialty scope of practice. In New Zealand rural nursing is an underrepresented aspect of nursing practice, is misunderstood and does not fit easily within the wider nursing profession and policies governing practice. This study situated within the New Zealand context adds to the international studies’ aligned with rural nursing practice. The study addresses a gap in the literature by striving to identify and strengthen the awareness of and increase rural nurses’ understanding and articulation of their changing and adapting identity and furthermore an opportunity to appreciate their contribution to the delivery of rural health care. In addition, this study adds to the growing global rural nursing knowledge and theoretical base. This research is a continuation of the author’s academic involvement and ongoing relationships with the rural nursing sector, national policy analysts and health care planners since the 1990s. These relationships have led to awareness, that despite rural nurses’ efforts to explain the particular nuances which make up their practice, there has been little recognition by profession to establish rural nursing as a specialty. The research explored why nurses’ who practiced in the rural Otago region of New Zealand, between the 1990s and early 2000s moved away from the traditional identity as a district, practice or public health nurse and looked towards a more appropriate identity which reflected their emerging practice. This qualitative research situated within the interpretive paradigm embeds this retrospective study within the discipline of nursing and engages with the concepts of place and governmentality. National key informant and Otago regional rural nurse interviews generated data and were analyzed using thematic analysis. Stemming from the analyses, an analytical diagrammatic matrix was developed demonstrating rural nursing as a ‘place–based practice’ governed both from within and beyond location presenting how the nurse aligns the self in the rural community as a meaningful provider of health care. Promoting this matrix may encourage a focal discussion point within the international spectrum of nursing and likewise between rural and non-rural nurses which it is hoped will generate further debate in relation to the different nuances aligned with rural nursing practice. Further, insights from this paper may capture key aspects and issues related to identity formation in respect to rural nurses, from the UK, New Zealand, Canada, USA, and Australia.

Keywords: matrix, place, nursing, rural

Procedia PDF Downloads 140

Authors: Sami W. Tabsh

Abstract:

The strength of reinforced concrete depends on the member dimensions and material properties. The properties of concrete and steel materials are not constant but random variables. The variability of concrete strength is due to batching errors, variations in mixing, cement quality uncertainties, differences in the degree of compaction and disparity in curing. Similarly, the variability of steel strength is attributed to the manufacturing process, rolling conditions, characteristics of base material, uncertainties in chemical composition, and the microstructure-property relationships. To account for such uncertainties, codes of practice for reinforced concrete design impose resistance factors to ensure structural reliability over the useful life of the structure. In this investigation, the effects of reductions in concrete and reinforcing steel strengths from the nominal values, beyond those accounted for in the structural design codes, on the structural reliability are assessed. The considered limit states are flexure, shear and axial compression based on the ACI 318-11 structural concrete building code. Structural safety is measured in terms of a reliability index. Probabilistic resistance and load models are compiled from the available literature. The study showed that there is a wide variation in the reliability index for reinforced concrete members designed for flexure, shear or axial compression, especially when the live-to-dead load ratio is low. Furthermore, variations in concrete strength have minor effect on the reliability of beams in flexure, moderate effect on the reliability of beams in shear, and sever effect on the reliability of columns in axial compression. On the other hand, changes in steel yield strength have great effect on the reliability of beams in flexure, moderate effect on the reliability of beams in shear, and mild effect on the reliability of columns in axial compression. Based on the outcome, it can be concluded that the reliability of beams is sensitive to changes in the yield strength of the steel reinforcement, whereas the reliability of columns is sensitive to variations in the concrete strength. Since the embedded target reliability in structural design codes results in lower structural safety in beams than in columns, large reductions in material strengths compromise the structural safety of beams much more than they affect columns.

Keywords: code, flexure, limit states, random variables, reinforced concrete, reliability, reliability index, shear, structural safety

Procedia PDF Downloads 430

Authors: Onyinyechi Joy Kingdom

Abstract:

Mergers and Acquisitions (M&A) have been proposed as a mechanism through which, problems associated with inefficiency or poor performance in financial institution could be addressed. The aim of this study is to examine the proposition that recapitalization of banks, which encouraged Mergers and Acquisitions in Nigeria banking system, would strengthen the domestic banks, improve financial deepening and the confidence of depositors. Hence, this study examines the impact of the 2005 M&A in the Nigerian-banking sector on financial deepening using mixed method (quantitative and qualitative approach). The quantitative process of this study utilised annual time series for financial deepening indicator for the period of 1997 to 2012. While, the qualitative aspect adopted semi-structured interview to collate data from three merged banks and three stand-alone banks to explore, understand and complement the quantitative results. Furthermore, a framework thematic analysis is employed to analyse the themes developed using NVivo 11 software. Using the quantitative approach, findings from the equality of mean test (EMT) used suggests that M&A have significant impact on financial deepening. However, this method is not robust enough given its weak validity as it does not control for other potential factors that may determine financial deepening. Thus, to control for other factors that may affect the level of financial deepening, a Multiple Regression Model (MRM) and Interrupted Times Series Analysis (ITSA) were applied. The coefficient for M&A dummy turned negative and insignificant using MRM. In addition, the estimated linear trend of the post intervention when ITSA was applied suggests that after M&A, the level of financial deepening decreased annually; however, this was statistically insignificant. Similarly, using the qualitative approach, the results from the interview supported the quantitative results from ITSA and MRM. The result suggests that interest rate should fall when capital base is increased to improve financial deepening. Hence, this study contributes to the existing literature the importance of other factors that may affect financial deepening and the economy when policies that will enhance bank performance and the economy are made. In addition, this study will enable the use of valuable policy instruments relevant to monetary authorities when formulating policies that will strengthen the Nigerian banking sector and the economy.

Keywords: mergers and acquisitions, recapitalization, financial deepening, efficiency, financial crisis

Procedia PDF Downloads 397

Authors: Deborah Idowu

Abstract:

This research delves into the effectiveness of explicitly teaching productive non-cognate French suffixes to English beginner learners of the French language. It is widely accepted that cognates, especially orthographic ones, can be inferred by learners from their first language (in this case, English). The same is the case for derived French words with cognate suffixes, provided the learner is familiar with the lemma, which can either be cognate or non-cognate. However, the same cannot be said for derived French words with non-cognate suffixes. These suffixes often pose challenges to learners, even when the base word is familiar to them. The primary goal of this research is to enhance the vocabulary comprehension and expansion of English-speaking beginners in French by focusing on the recognition of derived French words that may not align with their L1 knowledge. The methodology employed in this study of derivational morphology involves an experimental group receiving explicit instruction on productive non-cognate suffixes, while a control group does not. By utilizing confidence ratings and other analytical tools, the analysis aims to measure the impact of this targeted instruction on the learners' ability to understand and incorporate non-cognate suffixes into their French vocabulary. Through this experimental approach, the research seeks to provide valuable insights into how explicit instruction on non-cognate suffixes can benefit beginner French learners, ultimately aiding them in navigating the intricacies of French derivational morphology. The objectives of this research are as follows: i. to investigate the impact of explicitly teaching productive non-cognate suffixes on the vocabulary comprehension and expansion of beginner learners of the French language; ii. to assess the effectiveness of targeted instruction on non-cognate suffixes in aiding English-speaking learners in recognizing and understanding derived French words that may not align with their native language knowledge, iii. to compare the vocabulary acquisition and retention of beginner French learners who receive explicit instruction on non-cognate suffixes with those who do not to determine the effectiveness of this instructional approach, iv. to analyze the confidence ratings and other analytical methods to gauge the learners' ability to integrate non-cognate suffixes into their French vocabulary and comprehend the meaning of derived words more effectively, v. to contribute insights into how explicit instruction on non-cognate suffixes can enhance the overall language learning experience for beginner learners of French, particularly in the area of French derivational morphology.

Keywords: suffixes, derivational morphology, non-cognates, vocabulary acquisition, French language learners

Procedia PDF Downloads 37

Authors: Awatif Habeeb Al-Shamare

Abstract:

The number of social media users amongst special education teachers and parents of children with Down Syndrome (DS) is increasing annually. This is also the case in the Kingdom of Saudi Arabia (KSA). However, according to the best of the author’s knowledge, there are no qualitative studies which testify to the true nature of the interaction between teachers and parents when using social media, nor the role of social media in supporting and assisting parents and teachers with regards to the children’s educational needs in KSA. Therefore, this ongoing study aims to identify the role of social media in supporting parents and teachers of DS students, with a special emphasis on early intervention services in KSA. By bridging the knowledge gap on social media and special education in KSA and presenting socially relevant and applied information on the topic, this research provides a theoretical and practical base for the establishment of appropriate and effective programmes between the ministries of Information and Special Education in particular. A qualitative approach was selected because it was the most suitable approach for exploring the participants’ experiences, which could not be determined through scientific tests. Interviewing, chosen as the research instrument, allowed the researcher to obtain a detailed understanding of the topic linked to the study objectives. Initially, a pilot study was conducted at the Daycare Center in May 2016. Its aim was to examine and refine the methodology and assess whether the questions were understood with the potential for re-drafting them, if necessary. The main study consists of five teachers and five mothers with experience of using social media and with links to the Daycare Center. Thematic Analysis has been chosen for analysing the findings because it is a flexible method that allows themes to emerge from the data. Results of the current study are still in the initial stages, but the preliminary findings are as follows: (1) social media is an important tool in encouraging parents and teachers to access the necessary information and knowledge about, and experience in, early intervention services; (2) it acts as a support network for the parents; (3) it helps raise awareness about DS and the need for early intervention; (4) it can be used to put pressure on the government for an expansion in early intervention services, and finally (5) its use can be problematic in that parents and teachers face some difficulties and challenges when using the different platforms. It can be concluded that social media plays a significant role in the lives of teachers and parents with special needs children in KSA.

Keywords: down syndrome, early intervention services, social media, support parents and teachers

Procedia PDF Downloads 146

Authors: Hussien Ali, Mesfin Menza, Fitsum Hagos, Amare Haileslassie

Abstract:

Climate change has perverse effects on agricultural productivity and natural resource base, negatively affecting the well-being of the households and communities. The government and NGOs promote climate smart agricultural (CSA) practices to help farmers adapt to and mitigate the negative effects of climate change. This study aims to identify widely available CSA practices and examine their impacts on food security and multi-dimensional poverty of rural farm households in the Central Rift Valley, Ethiopia. Using three-stage proportional to size sampling procedure, the study randomly selected 278 households from two kebeles from four districts each. A cross-sectional data of 2020/21 cropping season was collected using structured and pretested survey questionnaire. Food consumption score, dietary diversity score, food insecurity experience scale, and multidimensional poverty index were calculated to measure households’ welfare indicators. Multinomial endogenous switching regression model was used to assess average treatment effects of CSA on these outcome indicators on adopter and non-adopter households. The results indicate that the widely adopted CSA practices in the area are conservation agriculture, soil fertility management, crop diversification, and small-scale irrigation. Adopter households have, on average, statistically higher food consumption score, dietary diversity score and lower food insecurity access scale than non-adopters. Moreover, adopter households, on average, have lower deprivation score in multidimensional poverty compared to non-adopter households. Up scaling the adoption of CSA practices through the improvement of households’ implementation capacity and better information, technical advice, and innovative financing mechanisms is advised. Up scaling CSA practices can further promote achieving global goals such as SDG 1, SDG 2, and SDG 13 targets, aimed to end poverty and hunger and mitigate the adverse impacts of climate change, respectively.

Keywords: climate-smart agriculture, food security, multidimensional poverty, upscaling CSA, Ethiopia

Procedia PDF Downloads 90