Search results for: wildland urban interface

Authors: Emanuel Teixeira, Anderson Ramos, Marisa Lourenço, Fernando J. Velez, Jon M. Peha

Abstract:

This article discusses the benefit cost analysis aspects of millimetre wavebands (mmWaves) and Super High Frequency (SHF). The devaluation along the distance of the carrier-to-noise-plus-interference ratio with the coverage distance is assessed by considering two different path loss models, the two-slope urban micro Line-of-Sight (UMiLoS) for the SHF band and the modified Friis propagation model, for frequencies above 24 GHz. The equivalent supported throughput is estimated at the 5.62, 28, 38, 60 and 73 GHz frequency bands and the influence of carrier-to-noise-plus-interference ratio in the radio and network optimization process is explored. Mostly owing to the lessening caused by the behaviour of the two-slope propagation model for SHF band, the supported throughput at this band is higher than at the millimetre wavebands only for the longest cell lengths. The benefit cost analysis of these pico-cellular networks was analysed for regular cellular topologies, by considering the unlicensed spectrum. For shortest distances, we can distinguish an optimal of the revenue in percentage terms for values of the cell length, R ≈ 10 m for the millimeter wavebands and for longest distances an optimal of the revenue can be observed at R ≈ 550 m for the 5.62 GHz. It is possible to observe that, for the 5.62 GHz band, the profit is slightly inferior than for millimetre wavebands, for the shortest Rs, and starts to increase for cell lengths approximately equal to the ratio between the break-point distance and the co-channel reuse factor, achieving a maximum for values of R approximately equal to 550 m.

Keywords: millimetre wavebands, SHF band, SINR, cost benefit analysis, 5G

Procedia PDF Downloads 141

Authors: Thais O. de Paula, Marjorie R. A. Sarmiento, Francis M. Borges, Alessandra B. Ferreira-Machado, Juliana A. Resende, Dioneia E. Cesar, Vania L. Silva, Claudio G. Diniz

Abstract:

Obesity is currently a worldwide public health threat, being considered a pandemic multifactorial disease related to the human gut microbiota (GM). Add to that GM is considered an important reservoir of antimicrobial resistance genes (ARG) and little is known on GM and ARG in obesity, considering the altered physiology and xenobiotics intake. As regional and social behavior may play important roles in GM modulation, and most of the studies are based on small sample size and various methodological approaches resulting in difficulties for data comparisons, this study was focused on the investigation of GM bacterial diversity in obese (OB), overweight (OW) and eutrophic individuals (ET) considering their nutritional, clinical and social characteristics; and comparative screening of AGR related to their physiology and xenobiotics intake. Microbial community was accessed by FISH considering phyla as a taxonomic level, and PCR-DGGE followed by dendrograms evaluation (UPGMA method) from fecal metagenome of 72 volunteers classified according to their body mass index (BMI). Nutritional, clinical, social parameters and xenobiotics intake were recorded for correlation analysis. The fecal metagenome was also used as template for PCR targeting 59 different ARG. Overall, 62% of OB were hypertensive, and 12% or 4% were, regarding the OW and ET individuals. Most of the OB were rated as low income (80%). Lower relative bacterial densities were observed in the OB compared to ET for almost all studied taxa (p < 0.05) with Firmicutes/Bacteroidetes ratio increased in the OB group. OW individuals showed a bacterial density representative of GM more likely to the OB. All the participants were clustered in 3 different groups based on the PCR-DGGE fingerprint patterns (C1, C2, C3), being OB mostly grouped in C1 (83.3%) and ET mostly grouped in C3 (50%). The cluster C2 showed to be transitional. Among 27 ARG detected, a cluster of 17 was observed in all groups suggesting a common core. In general, ARG were observed mostly within OB individuals followed by OW and ET. The ratio between ARG and bacterial groups may suggest that AGR were more related to enterobacteria. Positive correlations were observed between ARG and BMI, calories and xenobiotics intake (especially use of sweeteners). As with nutritional and clinical characteristics, our data may suggest that GM of OW individuals behave in a heterogeneous pattern, occasionally more likely to the OB or to the ET. Regardless the regional and social behaviors of our population, the methodological approaches in this study were complementary and confirmatory. The imbalance of GM over the health-disease interface in obesity is a matter of fact, but its influence in host's physiology is still to be clearly elucidated to help understanding the multifactorial etiology of obesity. Although the results are in agreement with observations that GM is altered in obesity, the altered physiology in OB individuals seems to be also associated to the increased xenobiotics intake and may interfere with GM towards antimicrobial resistance, as observed by the fecal metagenome and ARG screening. Support: FAPEMIG, CNPQ, CAPES, PPGCBIO/UFJF.

Keywords: antimicrobial resistance, bacterial diversity, gut microbiota, obesity

Procedia PDF Downloads 170

Authors: N. Damenia, E. Kharaishvili, N. Sagareishvili, M. Saghareishvili

Abstract:

Women's Employment is one of the most important issues in the global economy. The article discusses the stated topic in Georgia, through historical content, Soviet experience, and modern perspectives. The paper discusses segmentation insa terms of employment and related problems. Based on statistical analysis, women's unemployment rate and its factors are analyzed. The level of employment of women in Transcaucasia (Georgia, Armenia, and Azerbaijan) is discussed and is compared with Baltic countries (Lithuania, Latvia, and Estonia). The study analyzes women’s level of development, according to the average age of marriage and migration level. The focus is on Georgia's Association Agreement with the EU in 2014, which includes economic, social, trade and political issues. One part of it is gender equality at workplaces. According to the research, the average monthly remuneration of women managers in the financial and insurance sector equaled to 1044.6 Georgian Lari, while in overall business sector average monthly remuneration equaled to 961.1 GEL. Average salaries are increasing; however, the employment rate remains problematic. For example, in 2017, 74.6% of men and 50.8% of women were employed from a total workforce. It is also interesting that the proportion of men and women at managerial positions is 29% (women) to 71% (men). Based on the results, the main recommendation for government and civil society is to consider women as a part of the country’s economic development. In this aspect, the experience of developed countries should be considered. It is important to create additional jobs in urban or rural areas and help migrant women return and use their working resources properly.

Keywords: employment of women, segregation in terms of employment, women's employment level in Transcaucasia, migration level

Procedia PDF Downloads 117

Authors: Jelena Filipović, Milenko Košutić, Vladimir Filipović

Abstract:

In the last decades, the urban population has been characterized by sedentary lifestyles, low physical activity, and "fast food". These changes in diet and physical nonactivity have been associated with an increase in chronic diseases. Bread is one of the most popular wheat products consumed worldwide. Spelt wheat has shown potential in various food applications, including bread, pasta, breakfast cereal, and other products of altered nutritional characteristics compared to conventional wheat products. It has very high protein content and even 30 to 60% higher concentration of mineral elements Fe, Zn, Cu, Mg and P compared to Triticum Aestivum. Spelt wheat is growing without the use of pesticides in harsh ecological conditions and it is an old cultivar. So it can be used for organic and health-safe food. Changes in the formulation of bread with the aim of improving its nutritional and functional properties usually lead to changes in the dough's properties, which are related to the quality of the finished product. The aim of this paper is to research the impact of adding yeast extract to bread on sensory characteristics and consumer acceptance of a new product as a key factor for the successful marketing of a distinct product. The sensory analysis of bread with 5% yeast extract is as follows: the technological quality is very good (3.8), and the color of the product is excellent (4.85). Based on data, consumers' survey declared that they liked the taste of bread with 5% yeast extract (74%), consumers marked the product as likable (70%), and 75% of the total number of respondents would buy this new product. This paper is promoting a type of bread with 5% yeast extract (Z score 0.80) to improve diet and a product intended for consumers conscious about their health and diet.

Keywords: bread, yeast extract, sensory analysis, consumer survey, score analysis

Procedia PDF Downloads 61

Authors: Nigar Kantarci Carsibasi

Abstract:

Coarse-grained elastic network models, namely Gaussian network model (GNM) and Anisotropic network model (ANM), are utilized in order to investigate the fluctuation dynamics of Murine Double Minute 2 (MDM2), which is the native inhibitor of p53. Conformational dynamics of MDM2 are elucidated in unbound, p53 bound, and non-peptide small molecule inhibitor bound forms. With this, it is aimed to gain insights about the alterations brought to global dynamics of MDM2 by native peptide inhibitor p53, and two small molecule inhibitors (HDM201 and NVP-CGM097) that are undergoing clinical stages in cancer studies. MDM2 undergoes significant conformational changes upon inhibitor binding, carrying pieces of evidence of induced-fit mechanism. Small molecule inhibitors examined in this work exhibit similar fluctuation dynamics and characteristic mode shapes with p53 when complexed with MDM2, which would shed light on the design of novel small molecule inhibitors for cancer therapy. The results showed that residues Phe 19, Trp 23, Leu 26 reside in the minima of slowest modes of p53, pointing to the accepted three-finger binding model. Pro 27 displays the most significant hinge present in p53 and comes out to be another functionally important residue. Three distinct regions are identified in MDM2, for which significant conformational changes are observed upon binding. Regions I (residues 50-77) and III (residues 90-105) correspond to the binding interface of MDM2, including (α2, L2, and α4), which are stabilized during complex formation. Region II (residues 77-90) exhibits a large amplitude motion, being highly flexible, both in the absence and presence of p53 or other inhibitors. MDM2 exhibits a scattered profile in the fastest modes of motion, while binding of p53 and inhibitors puts restraints on MDM2 domains, clearly distinguishing the kinetically hot regions. Mode shape analysis revealed that the α4 domain controls the size of the cleft by keeping the cleft narrow in unbound MDM2; and open in the bound states for proper penetration and binding of p53 and inhibitors, which points to the induced-fit mechanism of p53 binding. P53 interacts with α2 and α4 in a synchronized manner. Collective modes are shifted upon inhibitor binding, i.e., second mode characteristic motion in MDM2-p53 complex is observed in the first mode of apo MDM2; however, apo and bound MDM2 exhibits similar features in the softest modes pointing to pre-existing modes facilitating the ligand binding. Although much higher amplitude motions are attained in the presence of non-peptide small molecule inhibitor molecules as compared to p53, they demonstrate close similarity. Hence, NVP-CGM097 and HDM201 succeed in mimicking the p53 behavior well. Elucidating how drug candidates alter the MDM2 global and conformational dynamics would shed light on the rational design of novel anticancer drugs.

Keywords: cancer, drug design, elastic network model, MDM2

Procedia PDF Downloads 130

Authors: Suhail Shersad

Abstract:

Introduction In developing countries, the access to higher education for the lower socioeconomic strata is very poor at less than 0.05%. The challenges faced by prospective students in these circumstances to pursue higher education have been explored through direct interaction with them and their families in urban slums of New Delhi. This study included evaluation of the demographics, social indices, expectations and perceptions of selected communities. Results The results show that the poor life expectancy, low exposure to technology, lack of social infrastructure and poor sanitary conditions have reduced their drive for academic achievements. This is despite a good level of intelligence and critical thinking skills among these students. The perception of the community including parents shows that despite their desire to excel, there are too may roadblocks to achieving a fruitful professional life for the next generation. Discussion The prerequisites of higher education may have to be revisited to be more inclusive of socially handicapped students. The knowledge, skills and attributes required for higher education system should form the baseline for creating a roadmap for higher secondary education suited for local needs. Conventional parameters like marks and grading have to be re-looked so that life skills and vocational training form part of the core curriculum. Essential skills should be incorporated at an earlier age, providing an alternative pathway for such students to join higher education. Conclusion: There is a need to bridge the disconnect that exists between higher education planning, the needs of the concerned cohorts and the existing higher secondary education. The variables that contribute to making such a decision have to be examined further. Keywords: prerequisites of higher education, social mobility, society expectations, access to higher education

Keywords: access to higher education, prerequisites of higher education, society expectations, social mobility

Procedia PDF Downloads 386

Authors: Anneke Van Biljon

Abstract:

Background: Exercise is a primary form of preventing and improving cardiometabolic disease risk factors; however specific exercise variables and their associated health benefits in children are inconclusive. A preliminary study revealed that different exercise variables may improve particular cardiometabolic health benefits. Objectives: This study further investigated the specific cardiometabolic health benefits associated with three isocaloric exercise interventions set at different intensities. Methods: Hundred-and-twenty (n = 120) participants between the ages of 10 – 14 years old were assigned to four different study groups 1. High intensity interval training (HIIT) at > 80% MHR 2. Moderate intensity continuous training (MICT) at 65% – 70% MHR 3. Alternative intensities (ALT) of HIIT and MICT 4. Control group. Exercise interventions were designed to generate isocaloric workloads of ~154.77 kcal per session, three times per week for five weeks. The one-way ANOVA test established comparisons between group means. Post hoc tests were calculated to determine specific group differences. Results: Although, all exercise groups improved cardiometabolic health, the MICT group showed greater improvements in fasting glucose (-9.30%), whereas cardiorespiratory fitness increased most by 31.33% (p = 0.000) within the HIIT group. Finally, ALT group recorded overall superior and additional cardiometabolic health benefits compared with both MICT and HIIT groups. Conclusion: The findings of this study indicate that superior benefits may be elicited when combining and alternating MICT and HIIT. These results provide specific exercise recommendations for achieving optimal and substantial cardiometabolic health benefits in children which will contribute towards achieving the health-related Sustainable Development Goals for 2030.

Keywords: cardiometabolic disease risk factors, exercise, pediatrics, interventions

Procedia PDF Downloads 248

Authors: Maria Viktoria Melgo

Abstract:

This study aimed to determine the possible association between calcium intake and wealth indices of selected female adults. Specifically, it aimed to: a) determine the calcium intake adequacy of the respondents. b) determine the relationship, if any, between calcium intake adequacy, area and wealth indices. The study used the survey design and employed convenience sampling in selecting participants. Two hundred females aged 20 – 64 years old were covered in the study from depressed and non-depressed areas. Data collected were calcium intake taken from two 24-hour food recall and Food Frequency Questionnaire (FFQ) and wealth indices using housing characteristics, household assets and access to utilities and infrastructure. Descriptive statistics and Chi-square test were used to determine the frequency distribution and association between the given variables, respectively, using Statistical Package for Social Sciences (SPSS) and OpenEpi software. The results showed that there were 86% of respondents in the depressed area with an inadequate calcium intake while there were 78% of respondents in the non-depressed area with an adequate calcium intake. No significant relationship was obtained in most wealth indices with calcium intake adequacy and area but appliance and ownership of main material of the house showed a significant relationship to calcium intake adequacy by area. The study recommends that the Local Government Unit (LGU) should provide seminars or nutrition education that will further enhance the knowledge of the people in the community. The study also recommends to conduct a similar study but with different, larger sample size, different location nonetheless if it is in urban or rural and include the anthropometry measurement of the respondents.

Keywords: association, calcium intake adequacy, metro Manila, Philippines, wealth indices

Procedia PDF Downloads 196

Authors: Mohammad Maeiyat, Ali Maeiyat Ivatlou, Rasul Fani Khiavi, Abouzar Maeiyat Ivatlou, Parya Maeiyat

Abstract:

Purpose: Considering the fact that visual impairment is still one of the countries health problem, this study was conducted to determine the causes of blindness and low vision in visually impaired membership of Ardabil Province welfare organization. Methods: The present study which was based on descriptive and national-census, that carried out in visually impaired population supported by welfare organization in all urban and rural areas of Ardabil Province in 2013 and Collection of samples lasted for 7 months. The subjects were inspected by optometrist to determine their visual status (blindness or low vision) and then referred to ophthalmologist in order to discover the main causes of visual impairment based on the international classification of diseases version 10. Statistical analysis of collected data was performed using SPSS software version 18. Results: Overall, 403 subjects with mean age of years participated in this study. 73.2% were blind, 26.8 % were low vision and according gender grouping 60.50 % of them were male, 39.50 % were female that divided into three groups with the age level of lower than 15 (11.2%) 15 to 49 (76.7%), and 50 and higher (12.1%). The age range was 1 to 78 years. The causes of blindness and low vision were in descending order: optic atrophy (18.4%), retinitis pigmentosa (16.8%), corneal diseases (12.4%), chorioretinal diseases (9.4%), cataract (8.9%), glaucoma (8.2%), phthisis bulbi (7.2%), degenerative myopia (6.9%), microphtalmos ( 4%), amblyopia (3.2%), albinism (2.5%) and nistagmus (2%). Conclusion: in this study the main causes of visual impairments were optic atrophy and retinitis pigmentosa, thus specific prevention plans can be effective in reducing the incidence of visual disabilities.

Keywords: blindness, low vision, welfare, ardabil

Procedia PDF Downloads 440

Authors: Robin Ruowei Yang

Abstract:

The Khitan-Liao dynasty (907-1125) was founded by the nomadic Khitan people and showed its peculiarities. This regime not only effectively ruled their own nomads, but also ruled the farming ethnic groups of the Han (漢) and others. It also controlled vast territories that included the northern border domains of China, East Asia, and even Central Asia. Different from the practice of other nomadic people, Khitan-Liao built settlement towns and cities on the Mongolia steppe from beginning of the dynasty, which made the politics, economy and culture of the steppe area develop significantly. In the process of cities’ construction, Khitan-Liao set up five capitals respectively. Except three of them were rebuilt or expanded based on existing cities in agricultural areas, two new capitals were built, namely up-capital (Shangjing) and middle-capital (Zhongjing) in the steppe area. This article takes the up-capital (Shangjing) as an example to investigate a special zone in the capital for settling movable tents which adapted Khitan nomads, especially its nomadic government officials to live in. By using primary Chinese historical records and newly archaeological excavations, this article examines how the special tent zone used by the Khitan rulers, discusses how the Khitan-Liao manifested its hybrid cultural characteristics in urban planning, and its implications in studying the history of Khitan-Liao. The information, discussion and argument presented in this article are also worth considering the influence of urbanization of Khitan-Liao’s urbaization on subsequent dynasties in pre-modern China and Inner Asia.

Keywords: cities on Steppe, special tent zone in cities, Khitan-Liao, hybrid culture

Procedia PDF Downloads 80

Authors: Ishmael Obaeko Iwara

Abstract:

The Point of Sale (POS) cash and cashless semi-formal business has emerged as a significant driver of employment in countries like Nigeria and Kenya, similar to other micro and small-scale enterprises. This business model enables individuals to establish cash in/out outlets, offering entrepreneurs and small business owners a lucrative opportunity to generate additional income. However, the benefits extend beyond employment, as the POS model has become an integral part of the payment system in these countries. It facilitates convenient fund transfers, cash deposits, and withdrawals for individuals residing in both urban and rural areas. Given South Africa's high youth unemployment rate and limited banking services in rural households, coupled with a vibrant informal business economy akin to Nigeria and Kenya, the POS model potentially presents a business opportunity for the unemployed and serves as a banking solution for remote communities. Nonetheless, its implementation within South Africa's entrepreneurial landscape remains a subject of contention. Through qualitative research employing a participatory community-led action research approach, this study analyzes feedback, critiques, and potential interventions from various stakeholders, including business actors, grassroots communities, financial institutions, and policymakers. The findings offer crucial insights into the challenges associated with the adoption of the POS model and suggest mitigating factors to facilitate its successful implementation.

Keywords: grassroots entrepreneurs, rural households, POS banking, youth employment

Procedia PDF Downloads 72

Authors: Robert Caulk

Abstract:

A generalized framework for adaptive machine learning deployments in algorithmic trading is introduced, tested, and released as open-source code. The presented software aims to test the hypothesis that recent data contains enough information to form a probabilistically favorable short-term price prediction. Further, the framework contains various adaptive machine learning techniques that are geared toward generating profit during strong trends and minimizing losses during trend changes. Results demonstrate that this adaptive machine learning approach is capable of capturing trends and generating profit. The presentation also discusses the importance of defining the parameter space associated with the dynamic training data-set and using the parameter space to identify and remove outliers from prediction data points. Meanwhile, the generalized architecture enables common users to exploit the powerful machinery while focusing on high-level feature engineering and model testing. The presentation also highlights common strengths and weaknesses associated with the presented technique and presents a broad range of well-tested starting points for feature set construction, target setting, and statistical methods for enforcing risk management and maintaining probabilistically favorable entry and exit points. The presentation also describes the end-to-end data processing tools associated with FreqAI, including automatic data fetching, data aggregation, feature engineering, safe and robust data pre-processing, outlier detection, custom machine learning and statistical tools, data post-processing, and adaptive training backtest emulation, and deployment of adaptive training in live environments. Finally, the generalized user interface is also discussed in the presentation. Feature engineering is simplified so that users can seed their feature sets with common indicator libraries (e.g. TA-lib, pandas-ta). The user also feeds data expansion parameters to fill out a large feature set for the model, which can contain as many as 10,000+ features. The presentation describes the various object-oriented programming techniques employed to make FreqAI agnostic to third-party libraries and external data sources. In other words, the back-end is constructed in such a way that users can leverage a broad range of common regression libraries (Catboost, LightGBM, Sklearn, etc) as well as common Neural Network libraries (TensorFlow, PyTorch) without worrying about the logistical complexities associated with data handling and API interactions. The presentation finishes by drawing conclusions about the most important parameters associated with a live deployment of the adaptive learning framework and provides the road map for future development in FreqAI.

Keywords: machine learning, market trend detection, open-source, adaptive learning, parameter space exploration

Procedia PDF Downloads 89

Authors: Nicholas Anarfi Bofah, James Damsere- Derry

Abstract:

There is increasing interest among institutions, governments, and international organisations to combat congestion, reduce contribution to green gases and provide sustainable urban transportation. College campuses are a preeminent setting for promoting active commuting to ameliorate a community's healthy lifestyle. Cycling is an important physical activity and has a long-term effect on health, and it is considered one of the top five interventions to reduce the prevalence of non-communicable diseases. The main objectives of the research were: (i) to identify students’ attitudes and behavior toward cycling usage, (ii) to identify barriers and opportunities for cycling on a university campus, and (iii) to construct tangible policy recommendations for promoting cycling in the vicinity of the university. The data used in this study were obtained from a survey conducted among students at the Kwame Nkrumah University of Science and Technology (KNUST) in Kumasi between May 2022 and September 2022. A convenient sampling method was used to recruit and interview 398 participants. Two survey assistants who are former students of the university were engaged to administer the questionnaires randomly to students at the selected locations. Descriptive statistics were employed in the analysis of the data. Out of the 398 questionnaires, bicycle ridership and ownership among university students were 57% and 39%, respectively. Generally, the desire to use a bicycle as a mode of transport on campus was 36%. The desire to use a bicycle on campus was more prevalent among males 41% compared to females 30%. There is a high potential for increasing bicycle use among students. Recommendations include the provision of bicycle lanes, public education on the use of bicycles, and a campus bicycle-sharing program.

Keywords: sustainable development, cycling, university campus, bicycle

Procedia PDF Downloads 88

Authors: Kanika Taneja, V. K. Soni, Kafeel Ahmad, Shamshad Ahmad

Abstract:

A severe dust storm generated from a western disturbance over north Pakistan and adjoining Afghanistan affected the north-west region of India between May 28 and 31, 2014, resulting in significant reductions in air quality and visibility. The air quality of the affected region degraded drastically. PM10 concentration peaked at a very high value of around 1018 μgm-3 during dust storm hours of May 30, 2014 at New Delhi. The present study depicts aerosol optical properties monitored during the dust days using ground based multi-wavelength Sky radiometer over the National Capital Region of India. High Aerosol Optical Depth (AOD) at 500 nm was observed as 1.356 ± 0.19 at New Delhi while Angstrom exponent (Alpha) dropped to 0.287 on May 30, 2014. The variation in the Single Scattering Albedo (SSA) and real n(λ) and imaginary k(λ) parts of the refractive index indicated that the dust event influences the optical state to be more absorbing. The single scattering albedo, refractive index, volume size distribution and asymmetry parameter (ASY) values suggested that dust aerosols were predominant over the anthropogenic aerosols in the urban environment of New Delhi. The large reduction in the radiative flux at the surface level caused significant cooling at the surface. Direct Aerosol Radiative Forcing (DARF) was calculated using a radiative transfer model during the dust period. A consistent increase in surface cooling was evident, ranging from -31 Wm-2 to -82 Wm-2 and an increase in heating of the atmosphere from 15 Wm-2 to 92 Wm-2 and -2 Wm-2 to 10 Wm-2 at top of the atmosphere.

Keywords: aerosol optical properties, dust storm, radiative transfer model, sky radiometer

Procedia PDF Downloads 377

Authors: Laila Niklasson

Abstract:

The aim of the study is to critically discuss how partner schools are engaged during Initial teacher education, ITE. The background is an experiment in Sweden where the practicum organization is reorganized due to a need to enhance quality during practicum. It is a national initiative from the government, supported by the National Agency of Education and lasts 2014-2019. The main features are concentration of students to school with a certain amount of mentors, mentors who have a mentor education and teachers with relevant subject areas and where there could be a mentor team with a leader at the school. An expected outcome is for example that the student teachers should be engaged in peer-learning. The schools should be supported by extra lectures from university teachers during practicum and also extra research projects where the schools should be engaged. A case study of one university based ITE was carried out to explore the consequences for the schools not selected. The result showed that from engaging x schools in a region, x was engaged. The schools are both in urban and rural areas, mainly in the latter. There is also a tendency that private schools are not engaged. On a unit level recruitment is perceived as harder for schools not engaged. In addition they cannot market themselves as ´selected school´ which can affect parent´s selection of school for their children. Also, on unit level, but with consequences for professional development, they are not selected for research project and thereby are not fully supported during school development. The conclusion is that from an earlier inclusive approach concerning professions where all teachers were perceived as possible mentors, there is a change to an exclusive approach where selected schools and selected teachers should be engaged. The change could be perceived as a change in governance mentality, but also in how professions are perceived, and development work is pursued.

Keywords: initial teacher education, practicum schools, profession, quality development

Procedia PDF Downloads 142

Authors: Kanchan Maji, Debasmita Pani, Sudip Dasgupta

Abstract:

Calcium phosphate cement (CPC) due to its high bioactivity and optimum bioresorbability shows excellent bone regeneration capability. Despite it has limited applications as bone implant due to its macro-porous microstructure causing its poor mechanical strength. The reinforcement of apatitic CPCs with biocompatible fibre glass phase is an attractive area of research to improve its mechanical strength. Here we study the setting behaviour of Si-doped and un-doped alpha tri-calcium phosphate (α-TCP) based CPC and its reinforcement with the addition of E-glass fibre. Alpha tri-calcium phosphate powders were prepared by solid state sintering of CaCO3, CaHPO4 and tetra ethyl ortho silicate (TEOS) was used as silicon source to synthesise Si doped α-TCP powders. Alpha tri-calcium phosphate based CPC hydrolyzes to form hydroxyapatite (HA) crystals having excellent osteoconductivity and bone-replacement capability thus self-hardens through the entanglement of HA crystals. Setting time, phase composition, hydrolysis conversion rate, microstructure, and diametral tensile strength (DTS) of un-doped CPC and Si-doped CPC were studied and compared. Both initial and final setting time of the developed cement was delayed because of Si addition. Crystalline phases of HA (JCPDS 9-432), α-TCP (JCPDS 29-359) and β-TCP (JCPDS 9-169) were detected in the X-ray diffraction (XRD) pattern after immersion of CPC in simulated body fluid (SBF) for 0 hours to 10 days. The intensities of the α-TCP peaks of (201) and (161) at 2θ of 22.2°and 24.1° decreased when the time of immersion of CPC in SBF increased from 0 hours to 10 days, due to its transformation into HA. As Si incorporation in the crystal lattice stabilised the TCP phase, Si doped CPC showed a little slower rate of conversion into HA phase as compared to un-doped CPC. The SEM image of the microstructure of hardened CPC showed lower grain size of HA in un-doped CPC because of premature setting and faster hydrolysis of un-doped CPC in SBF as compared that in Si-doped CPC. Premature setting caused generation of micro and macro porosity in un-doped CPC structure which resulted in its lower mechanical strength as compared to that in Si-doped CPC. This lower porosity and greater compactness in the microstructure attributes to greater DTS values observed in Si-doped CPC. E-glass fibres of the average diameter of 12 μm were cut into approximately 1 mm in length and immersed in SBF to deposit carbonated apatite on its surface. This was performed to promote HA crystal growth and entanglement along the fibre surface to promote stronger interface between dispersed E-glass fibre and CPC matrix. It was found that addition of 10 wt% of E-glass fibre into Si-doped α-TCP increased the average DTS of CPC from 8 MPa to 15 MPa as the fibres could resist the propagation of crack by deflecting the crack tip. Our study shows that biocompatible E-glass fibre in optimum proportion in CPC matrix can enhance the mechanical strength of CPC without affecting its bioactivity.

Keywords: Calcium phosphate cement, biocompatibility, e-glass fibre, diametral tensile strength

Procedia PDF Downloads 346

Authors: Alexandros Pournaras, Anastasia Papadopoulou, Serafim Kontos, Anastasios Karakostas

Abstract:

The air quality of modern cities is an important concern, as poor air quality contributes to human health and environmental issues. Reliable air quality forecasting has, thus, gained scientific and governmental attention as an essential tool that enables authorities to take proactive measures for public safety. In this study, the potential of Machine Learning (ML) models to forecast PM2.5 at local scale is investigated in the city of Thessaloniki, the second largest city in Greece, which has been struggling with the persistent issue of air pollution. ML models, with proven ability to address timeseries forecasting, are employed to predict the PM2.5 concentrations and the respective Air Quality Index 5-days ahead by learning from daily historical air quality and meteorological data from 2014 to 2016 and gathered from two stations with different land use characteristics in the urban fabric of Thessaloniki. The performance of the ML models on PM2.5 concentrations is evaluated with common statistical methods, such as R squared (r²) and Root Mean Squared Error (RMSE), utilizing a portion of the stations’ measurements as test set. A multi-categorical evaluation is utilized for the assessment of their performance on respective AQIs. Several conclusions were made from the experiments conducted. Experimenting on MLs’ configuration revealed a moderate effect of various parameters and training schemas on the model’s predictions. Their performance of all these models were found to produce satisfactory results on PM2.5 concentrations. In addition, their application on untrained stations showed that these models can perform well, indicating a generalized behavior. Moreover, their performance on AQI was even better, showing that the MLs can be used as predictors for AQI, which is the direct information provided to the general public.

Keywords: Air Quality, AQ Forecasting, AQI, Machine Learning, PM2.5

Procedia PDF Downloads 77

Authors: Șercăianu Mihai, Aldea Mihaela, Iacoboaea Cristina, Luca Oana, Nenciu Ioana

Abstract:

The rise and mitigation of unauthorized illegal waste dumps are a significant global issue within waste management ecosystems, impacting disadvantaged communities. Globally, including in Romania, many individuals live in houses without legal recognition, lacking ownership or construction permits, in areas known as "informal settlements." An increasing number of regions and cities in Romania are struggling to manage their illegal waste dumps, especially in the context of increasing poverty and lack of regulation related to informal settlements. One such informal settlement is located at the end of Bistra Street in Câlnic, within the Reșița Municipality of Caras Severin County. The article presents a case study that focuses on employing remote sensing techniques and spatial data to monitor and map illegal waste practices, with subsequent integration into a geographic information system tailored for the Reșița community. In addition, the paper outlines the steps involved in devising strategies aimed at enhancing waste management practices in disadvantaged areas, aligning with the shift toward a circular economy. Results presented in the paper contain a spatial mapping and visualization methodology calibrated with in situ data collection applicable for identifying illegal landfills. The emergence and neutralization of illegal dumps pose a challenge in the field of waste management. These approaches, which prove effective where conventional solutions have failed, need to be replicated and adopted more wisely.

Keywords: informal settlements, GIS, waste dumps, waste management, monitoring

Procedia PDF Downloads 88

Authors: W. Baumgartner, M. Welti, N. Hild, S. C. Hess, W. J. Stark, G. Meier Bürgisser, P. Giovanoli, J. Buschmann

Abstract:

Perfusion bioreactors are used to solve problems in tissue engineering in terms of sufficient nutrient and oxygen supply. Such problems especially occur in critical size grafts because vascularization is often too slow after implantation ending up in necrotic cores. Biominerizable and biocompatible nanocomposite materials are attractive and suitable scaffold materials for bone tissue engineering because they offer mineral components in organic carriers – mimicking natural bone tissue. In addition, human adipose derived stem cells (ASCs) can potentially be used to increase bone healing as they are capable of differentiating towards osteoblasts or endothelial cells among others. In the present study, electrospun nanocomposite disks of poly-lactic-co-glycolic acid and amorphous calcium phosphate nanoparticles (PLGA/a-CaP) were seeded with human ASCs and eight disks were stacked in a bioreactor running with normal culture medium (no differentiation supplements). Under continuous perfusion and uniaxial cyclic compression, load-displacement curves as a function of time were assessed. Stiffness and energy dissipation were recorded. Moreover, stem cell densities in the layers of the piled scaffold were determined as well as their morphologies and differentiation status (endothelial cell differentiation, chondrogenesis and osteogenesis). While the stiffness of the cell free constructs increased over time caused by the transformation of the a-CaP nanoparticles into flake-like apatite, ASC-seeded constructs showed a constant stiffness. Stem cell density gradients were histologically determined with a linear increase in the flow direction from the bottom to the top of the 3.5 mm high pile (r2 > 0.95). Cell morphology was influenced by the flow rate, with stem cells getting more roundish at higher flow rates. Less than 1 % osteogenesis was found upon osteopontin immunostaining at the end of the experiment (9 days), while no endothelial cell differentiation and no chondrogenesis was triggered under these conditions. All ASCs had mainly remained in their original pluripotent status within this time frame. In summary, we have fabricated a critical size bone graft based on a biominerizable bone-biomimetic nanocomposite with preserved stiffness when seeded with human ASCs. The special feature of this bone graft was that ASC densities inside the piled construct varied with a linear gradient, which is a good starting point for tissue engineering interfaces such as bone-cartilage where the bone tissue is cell rich while the cartilage exhibits low cell densities. As such, this tissue-engineered graft may act as a bone-cartilage interface after the corresponding differentiation of the ASCs.

Keywords: bioreactor, bone, cartilage, nanocomposite, stem cell gradient

Procedia PDF Downloads 308

Authors: Hira Jabbar

Abstract:

Education is vital for inclusive growth of an economy and a critical contributor for investment in human capital. Like other developing countries, Pakistan is facing enormous challenges regarding the provision of public facilities, improper infrastructure planning, accelerating rate of population and poor accessibility. The influence of the rapid advancement and innovations in GIS and RS techniques have proved to be a useful tool for better planning and decision making to encounter these challenges. Therefore present study incorporates GIS and RS techniques to investigate the spatial distribution of school facilities, identifies settlements with served and unserved population, finds potential areas for new schools based on population and develops an accessibility index to evaluate the higher accessibility for schools. For this purpose high-resolution worldview imagery was used to develop road network, settlements and school facilities and to generate school accessibility for each level. Landsat 8 imagery was utilized to extract built-up area by applying pre and post-processing models and Landscan 2015 was used to analyze population statistics. Service area analysis was performed using network analyst extension in ArcGIS 10.3v and results were evaluated for served and underserved areas and population. An accessibility tool was used to evaluate a set of potential destinations to determine which is the most accessible with the given population distribution. Findings of the study may contribute to facilitating the town planners and education authorities for understanding the existing patterns of school facilities. It is concluded that GIS and remote sensing can be effectively used in urban transport and facility planning.

Keywords: accessibility, geographic information system, landscan, worldview

Procedia PDF Downloads 325

Authors: Nicoly Coelho, Eduardo Vieira Vilas Boas, Paulo Orestes Formigoni

Abstract:

Faced with the remarkable developments in the various segments of modern engineering, provided by the increasing technological development, professionals of all educational areas need to overcome the difficulties generated due to the good understanding of those who are starting their academic journey. Aiming to overcome these difficulties, this article aims at an introduction to the basic study of numerical methods applied to fluid mechanics and thermodynamics, demonstrating the modeling and simulations with its substance, and a detailed explanation of the fundamental numerical solution for the use of finite difference method, using SCILAB, a free software easily accessible as it is free and can be used for any research center or university, anywhere, both in developed and developing countries. It is known that the Computational Fluid Dynamics (CFD) is a necessary tool for engineers and professionals who study fluid mechanics, however, the teaching of this area of knowledge in undergraduate programs faced some difficulties due to software costs and the degree of difficulty of mathematical problems involved in this way the matter is treated only in postgraduate courses. This work aims to bring the use of DFC low cost in teaching Transport Phenomena for graduation analyzing a small classic case of fundamental thermodynamics with Scilab® program. The study starts from the basic theory involving the equation the partial differential equation governing heat transfer problem, implies the need for mastery of students, discretization processes that include the basic principles of series expansion Taylor responsible for generating a system capable of convergence check equations using the concepts of Sassenfeld, finally coming to be solved by Gauss-Seidel method. In this work we demonstrated processes involving both simple problems solved manually, as well as the complex problems that required computer implementation, for which we use a small algorithm with less than 200 lines in Scilab® in heat transfer study of a heated plate in rectangular shape on four sides with different temperatures on either side, producing a two-dimensional transport with colored graphic simulation. With the spread of computer technology, numerous programs have emerged requiring great researcher programming skills. Thinking that this ability to program DFC is the main problem to be overcome, both by students and by researchers, we present in this article a hint of use of programs with less complex interface, thus enabling less difficulty in producing graphical modeling and simulation for DFC with an extension of the programming area of experience for undergraduates.

Keywords: numerical methods, finite difference method, heat transfer, Scilab

Procedia PDF Downloads 387

Authors: Yuxiao Jiang, Lingjun Meng, Mengyu Zhan, Lichunyi Zhang, Yingxia Yun

Abstract:

On August 8th of 2015, a serious explosion occurred in Binhai New Area of Tianjin. This explosion led to the suspension of Tianjin-Binhai Light Rail Line 9 which was an important transportation mean connecting the old and new urban areas and the suspension causes inconvenience to commuters traveling from Tianjin to Binhai or Binhai to Tianjin and residents living by Line 9. On this regard, this paper intends to give suggestions on how to develop multi-mode transportation system rapidly and effectively after a disaster and tackle with the problems in terms of transportation infrastructure facilities. The paper proposes the idea of traffic resilience which refers to the city’s ability to restore its transportation system and reduce risks when the transportation system is destroyed by a disaster. By doing questionnaire research, on the spot study and collecting data from the internet, a GIS model is established so as to analyze the alternative traffic means used by different types of residents and study the transportation supply and demand. The result shows that along the Line 9, there is a larger demand for alternative traffic means in the place which is nearer to the downtown area. Also, the distribution of bus stations is more reasonable in the place nearer to downtown area, however, the traffic speed in the area is slower. Based on traffic resilience, the paper raises strategies to develop post-disaster multi-mode transportation system such as establishing traffic management mechanism timely and effectively, building multi-mode traffic networks, improving intelligent traffic systems and so on.

Keywords: traffic resilience, multi-mode transportation system, public traffic, transportation demand

Procedia PDF Downloads 348

Authors: Néstor Iván Rojas, Wilson Medina Sierra

Abstract:

Managing spatial information is described through a Geographic Information System (GIS), for some neighborhoods in the city of Tunja, in relation to the structural typology of the buildings. The use of GIS provides tools that facilitate the capture, processing, analysis and dissemination of cartographic information, product quality evaluation of the classification of buildings. Allows the development of a method that unifies and standardizes processes information. The project aims to generate a geographic database that is useful to the entities responsible for planning and disaster prevention and care for vulnerable populations, also seeks to be a basis for seismic vulnerability studies that can contribute in a study of urban seismic microzonation. The methodology consists in capturing the plat including road naming, neighborhoods, blocks and buildings, to which were added as attributes, the product of the evaluation of each of the housing data such as the number of inhabitants and classification, year of construction, the predominant structural systems, the type of mezzanine board and state of favorability, the presence of geo-technical problems, the type of cover, the use of each building, damage to structural and non-structural elements . The above data are tabulated in a spreadsheet that includes cadastral number, through which are systematically included in the respective building that also has that attribute. Geo-referenced data base is obtained, from which graphical outputs are generated, producing thematic maps for each evaluated data, which clearly show the spatial distribution of the information obtained. Using GIS offers important advantages for spatial information management and facilitates consultation and update. Usefulness of the project is recognized as a basis for studies on issues of planning and prevention.

Keywords: microzonation, buildings, geo-processing, cadastral number

Procedia PDF Downloads 334

Authors: Wei Kunkun, Cao Wanyang, Xu Yujie, Qiao Yuzhi, Liu Yingning

Abstract:

The reasonable design of bus parking spaces can improve the traffic capacity of the station and reduce traffic congestion. In order to reasonably determine the number of berths at BRT (Bus Rapid Transit) stops, it is based on the actual bus rapid transit station observation data, scheduling data, and passenger flow data. Optimize the number of station berths from the perspective of optimizing the balance of supply and demand at the site. Combined with the classical capacity calculation model, this paper first analyzes the important factors affecting the traffic capacity of BRT stops by using SPSS PRO and MATLAB programming software, namely the distribution of BRT stops and the distribution of BRT stop time. Secondly, the method of calculating the number of the classic human capital management (HCM) model is optimized based on the actual passenger demand of the station, and the method applicable to the actual number of station berths is proposed. Taking Gangding Station of Zhongshan Avenue Bus Rapid Transit Corridor in Guangzhou as an example, based on the calculation method proposed in this paper, the number of berths of sub-station 1, sub-station 2 and sub-station 3 is 2, which reduces the road space of the station by 33.3% compared with the previous berth 3 of each sub-station, and returns to social vehicles. Therefore, under the condition of ensuring the passenger flow demand of BRT stations, the road space of the station is reduced, and the road is returned to social vehicles, the traffic capacity of social vehicles is improved, and the traffic capacity and efficiency of the BRT corridor system are improved as a whole.

Keywords: urban transportation, bus rapid transit station, HCM model, capacity, number of berths

Procedia PDF Downloads 95

Authors: Dolly Kumari, H. Lhungdim

Abstract:

Maternal health is one of the crucial health indicators for any country. 5th goal of Millennium Development Goals is also emphasising on improvement of maternal health. Soon after Independence government of India realizing the importance of maternal and child health care services, and took steps to strengthen in 1st and 2nd five year plans. In past decade the other health indicator which is life expectancy at birth has been observed remarkable improvement. But still maternal mortality is high in India and in some states it is observe much higher than national average. Government of India pour lots of fund and initiate National Rural Health Mission (NRHM) in 2005 to improve maternal health in country by providing affordable and accessible health care services. Accredited Social Heath Activist (ASHA) is one of the key components of the NRHM. Mainly ASHAs are selected female aged 25-45 years from village itself and accountable for the monitoring of maternal health care for the same village. ASHA are trained to works as an interface between the community and public health system. This study tries to assess the role of ASHA in utilizing maternal health care services and to see the level of awareness about benefits given under JSY scheme and utilization of those benefits by eligible women. For the study concurrent evaluation data from National Rural health Mission (NRHM), initiated by government of India in 2005 has been used. This study is based on 78205 currently married women from 70 different districts of India. Descriptive statistics, chi2 test and binary logistic regression have been used for analysis. The probability of institutional delivery increases by 2.03 times (p<0.001) while if ASHA arranged or helped in arranging transport facility the probability of institutional delivery is increased by 1.67 times (p<0.01) than if she is not arranging transport facility. Further if ASHA facilitated to get JSY card to the pregnant women probability of going for full ANC is increases by 1.36 times (p<0.05) than reference. However if ASHA discuses about institutional delivery and approaches to get register than probability of getting TT injection is 1.88 and 1.64 times (p<0.01) higher than that if she did not discus. Further, Probability of benefits from JSY schemes is 1.25 times (p<0.001) higher among women who get married after 18 years. The probability of benefits from JSY schemes is 1.25 times (p<0.001) higher among women who get married after 18 year of age than before 18 years, it is also 1.28 times (p<0.001) and 1.32 times (p<0.001) higher among women have 1 to 8 year of schooling and with 9 and above years of schooling respectively than the women who never attended school. Those women who are working have 1.13 times (p<0.001) higher probability of getting benefits from JSY scheme than not working women. Surprisingly women belongs to wealthiest quintile are .53times (P<0.001) less aware about JSY scheme. Results conclude that work done by ASHA has great influence on maternal health care utilization in India. But results also show that still substantial numbers of needed population are far from utilization of these services. Place of delivery is significantly influenced by referral and transport facility arranged by ASHA.

Keywords: institutional delivery, JSY beneficiaries, referral faculty, public health

Procedia PDF Downloads 330

Authors: Jelena Filipović, Milenko Košutić, Vladimir Filipović

Abstract:

In the last decades urban population is characterized by sedentary lifestyles, low physical activity and "fast food". These changes in diet and physical non activity have been associated with the increase of chronic non diseases. Bread is one of the most popularly wheat products consumed worldwide. Spelt wheat has shown potential in various food applications, including bread, pasta, breakfast cereal and other products of altered nutritional characteristics compared to conventional wheat products. It has very high protein content and even 30 to 60% higher concentration of mineral elements Fe, Zn, Cu, Mg and P compared to Triticum Aestivum. Spelt wheat is growing without the use of pesticides in harsh ecological conditions and it is an old cultivar. So it can be used for organic and health safe food. Changes in the formulation of bread with the aim to improve their nutritional and functional properties usually lead to changes in the dough properties which is related reflected to the quality of the finished product. The aim of this paper is researching the impact of adding yeast extract to bread on sensory characteristics and consumer acceptance of a new product as a key factor for successful marketing of a new product. The sensory analysis of bread with 5% yeast extract is as follows: the technological quality is very good (3.8) and the color of the product is excellent (4.85). Based on data consumers survey declared that they liked the taste of bread with 5% yeast extract (74%), consumers marked the product as likeable (70%), and 75% of the total number of respondents would buy this new product. This paper is promoting a new type of bread with 5% yeast extract (Z score 0.80) to improve diet and novel functional product which intended for consumers conscious about their health and diet.

Keywords: bread, yeast extract, sensory analysis, consumer survey, score analysis Z

Procedia PDF Downloads 56

Authors: Smriti Gour, Neelam Pandey

Abstract:

The objective of this study was to describe and analyse the mutual relationship between the coping mechanisms used by the families of a child with Autism Spectrum Disorder (ASD) and family dynamics and the effect sibling interactions have on the dynamics and coping mechanisms in an urban setup. In-depth interviews were conducted for 25 families, with 4 members each in the Delhi NCR area in India. The families who were interviewed had a younger child who had received a diagnosis of ASD between the ages of 5-12. The in-depth questionnaires contained open-ended questions and the interviews were conducted separately for the mother, father and the typically developing sibling. The key findings of the study suggested that lack of communication was a common factor in most families (n=19) leading to other difficulties like stress and relationship dysfunction. It also fostered a fallacious perception of the relationship dynamics in the family in most of the interviewed families and changed depending on the family member being interviewed. In families where the typically developing elder sibling had a good relationship with the autistic child, the family dynamics were found to be more stable, and the overall family well-being was better maintained. The coping mechanisms employed by the families were also more positive and tended to work better if the typically developing sibling maintained a positive and interactive relationship with the parents and the autistic child. The type of coping mechanisms had a major impact on the relationship between the parents and in dictating the dynamics of the family of the child with ASD. Spirituality, professional help, family support and household help emerged to be the most effective coping mechanisms for the families, with spirituality emerging to be the most positive and effective coping mechanism in the families interviewed.

Keywords: autism spectrum disorder, coping mechanism, family dynamics, parental relationships, siblings

Procedia PDF Downloads 318

Authors: Phyo Kyaw Kyaw

Abstract:

In the Yangon urban landscape, one could not help, but notice old buildings from the colonial period along with condominium developments recently, and many walk-up apartment buildings to accommodate the urbanization, growing population and social-economic status of Myanmar people. Walk-up apartments were built and popular after the British colonial period (around 1950s) and are still built up to today due to its cost-effectiveness and to accommodate low to mid-income residents in the metropolitan Yangon. Approximately 90% of apartment buildings are walk-up apartments. The common impression of walk-up apartments in Yangon appears to be old rectangular box shape, homogenous envelope and limited square feet dull interior small space. In other words, the buildings are full of constraints, lack of good user experiences, and they are not well-fitted in the modern days. Therefore, the resident suffers consequently many years, some may live in the apartment their entire lives. Thousands of people living in the walk-up apartment on a daily basis are being shaped by the space and its inadequate quality of living. Can it be called “Home” by the dwellers or is the place a temporary shelter?. Online semi-structured interviews of 15 apartments’ residents and online questionnaire surveys of 70 apartment residents are conducted. This research aims to explore what makes “Home” “A sense of Home” for walk-up apartment users in Yangon, Myanmar by studying subjective responses shaped by the interior and experience of the spaces in apartment to understand the perception of the residents and improve the quality of living. The result reflects the priority level of important factors in relation to the sense of home framework.

Keywords: home, living quality, space, perception, residents, walk-up apartment, Yangon

Procedia PDF Downloads 108

Authors: P. V. S. Mascarenhas, B. C. P. Albuquerque, D. J. F. Campos, L. L. Almeida, V. R. Domingues, L. C. S. M. Ozelim

Abstract:

Retaining slope structures are increasingly considered in geotechnical engineering projects due to extensive urban cities growth. These kinds of engineering constructions may present instabilities over the time and may require reinforcement or even rebuilding of the structure. In this context, statistical analysis is an important tool for decision making regarding retaining structures. This study approaches the failure probability of the construction of a retaining wall over the debris of an old and collapsed one. The new solution’s extension length will be of approximately 350 m and will be located over the margins of the Lake Paranoá, Brasilia, in the capital of Brazil. The building process must also account for the utilization of the ruins as a caisson. A series of in situ and laboratory experiments defined local soil strength parameters. A Standard Penetration Test (SPT) defined the in situ soil stratigraphy. Also, the parameters obtained were verified using soil data from a collection of masters and doctoral works from the University of Brasília, which is similar to the local soil. Initial studies show that the concrete wall is the proper solution for this case, taking into account the technical, economic and deterministic analysis. On the other hand, in order to better analyze the statistical significance of the factor-of-safety factors obtained, a Monte Carlo analysis was performed for the concrete wall and two more initial solutions. A comparison between the statistical and risk results generated for the different solutions indicated that a Gabion solution would better fit the financial and technical feasibility of the project.

Keywords: economical analysis, probability of failure, retaining walls, statistical analysis

Procedia PDF Downloads 406

Authors: Rita Chattopadhyay, Vivek Anand Thoutam

Abstract:

Speech is the most acceptable means of communication where we can quickly exchange our feelings and thoughts. Quite often, people can communicate orally but cannot interact or work with computers or devices. It’s easy and quick to give speech commands than typing commands to computers. In the same way, it’s easy listening to audio played from a device than extract output from computers or devices. Especially with Robotics being an emerging market with applications in warehouses, the hospitality industry, consumer electronics, assistive technology, etc., speech-based human-machine interaction is emerging as a lucrative feature for robot manufacturers. Considering this factor, the objective of this paper is to design the “Audio-Visual Co-Data Processing Pipeline.” This pipeline is an integrated version of Automatic speech recognition, a Natural language model for text understanding, object detection, and text-to-speech modules. There are many Deep Learning models for each type of the modules mentioned above, but OpenVINO Model Zoo models are used because the OpenVINO toolkit covers both computer vision and non-computer vision workloads across Intel hardware and maximizes performance, and accelerates application development. A speech command is given as input that has information about target objects to be detected and start and end times to extract the required interval from the video. Speech is converted to text using the Automatic speech recognition QuartzNet model. The summary is extracted from text using a natural language model Generative Pre-Trained Transformer-3 (GPT-3). Based on the summary, essential frames from the video are extracted, and the You Only Look Once (YOLO) object detection model detects You Only Look Once (YOLO) objects on these extracted frames. Frame numbers that have target objects (specified objects in the speech command) are saved as text. Finally, this text (frame numbers) is converted to speech using text to speech model and will be played from the device. This project is developed for 80 You Only Look Once (YOLO) labels, and the user can extract frames based on only one or two target labels. This pipeline can be extended for more than two target labels easily by making appropriate changes in the object detection module. This project is developed for four different speech command formats by including sample examples in the prompt used by Generative Pre-Trained Transformer-3 (GPT-3) model. Based on user preference, one can come up with a new speech command format by including some examples of the respective format in the prompt used by the Generative Pre-Trained Transformer-3 (GPT-3) model. This pipeline can be used in many projects like human-machine interface, human-robot interaction, and surveillance through speech commands. All object detection projects can be upgraded using this pipeline so that one can give speech commands and output is played from the device.

Keywords: OpenVINO, automatic speech recognition, natural language processing, object detection, text to speech

Procedia PDF Downloads 80